Question about 1997 Dodge Ram 2500 Club Cab

Open Question

07 how to fit top hinge on drivers door.peugeot 207

Creaking

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
geo5734036
  • 528 Answers

SOURCE: Driver door has dropped about 1/2". I see a torx

Before attempting to adjust the door, you need to check the wear on the hinge pins. Open the door fully and look at the middle of the hinge. See the pin there? Lift up on the latch side of the door as you watch the hinge pin. If you see the hinge moving around the pin or see the pin shifting back and forth then the metal grommet the pin goes through is worn and needs replacing. Motormite makes a replacement pin set that comes with new grommets ( or bushings to some). It's not so hard to change, but it can be a little tricky. Jack up the door to relieve the pressure on the pin.Start with the top pin. Watch the pin as you jack and keep going until the pin is in the middle of the movement range. Tap the old pin out and then inspect the grommet to see if it's worn past the outer edge of the metal. If it is worn past the edge then you'll need to replace that hinge. Otherwise, you can use that old pin to tap out the old grommet, and replace with the new one, then the new pin. slowly release the pressure on the jack and watch the new pin for excessive movement, then do the bottom pin and grommet.. Test door swing and alignment. If the door still hits low on the catch post, loosen those torq bolts after lifting the door slightly and now lift the door the distance it was low plus 1/8 inch. retighten torq bolts and release jack, then retest the door alignment to the catch post. Don't let the door strike the catch post hard - just let it slowly come into contact as you watch for alignment. Repeat procedure until door lines up centered on taht catch post.
Good luck!!

Posted on Nov 07, 2010

Testimonial: "Thank you so very much for the detailed response. I'll be working on it later today after church. Thanks again..."

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the coolant sensor on a Peugeot 207 1.4


part supplied says a spanner
undo the wire connector
undo the sensor
fit the new sensor
fit wore connector
if coolant is lost refill cooling system to correct level

Tridon Coolant Temperature Sensor, TCS172
fits PEUGEOT 207 1.4 16V,1.6 16V



26274348-wjya3n2etfq4tuodlgyyifbb-2-0.jpg

Sep 04, 2016 | Peugeot 207 Cars & Trucks

1 Answer

How do i fit spot lights to my peugeot 207 i have no holes in the bumper


When the lights were specified on the build order in 2007, a bumper containing the lights was installed. Peugeot did not plan for later installation of the lights.

Aug 20, 2016 | 2007 Peugeot 207 1.4

1 Answer

Passenger door has dropped and has to be lifted to close can any one give any guidance


Your hinges are bad. Depending on the model, sometimes th hinge pin(s) can be replaced without removing the door or hinges. Usually replacing the upper hinge will cure that problem.

Aug 29, 2017 | 2006 Peugeot 207 1.4

1 Answer

Where is the fuel filter on a Peugeot 207 cc


Fuel filters are only fitted to Peugeot petrol engined cars in countries where poor quality fule is an issue.

Sep 05, 2013 | 2008 Peugeot 207 CC

2 Answers

How do I remove the bonnet of my Peugeot 207?


needs 3 people
one to hold the bonnet up and one on each side to undo the hinge bolts and gas struts if used
replacement is reverse with an adjustment before the bolts are properly tightened
about 10 minutes work

Jun 30, 2017 | 2006 Peugeot 207 1.6

1 Answer

How to replace front driver door hinge check strap


a lot of door check straps only use a rolled spring pin. If this is broken and you can remove the door trim it will be fixable mostly.

Jan 13, 2013 | 2001 Peugeot 206 1.6

1 Answer

Where is fuel filter on my peouguet 207


Fuel filters are only fitted to Peugeot petrol engined cars in countries where poor quality fule is an issue.

Nov 30, 2012 | 2007 Peugeot 207 1.4

2 Answers

Ford ka creaking on drivers side when driving over bumps in road or turning


Is this a suspension creak, or a door creak?

Components which you haven't had changed are:

bottom suspension arms
Anti roll bar links

Also lubricate your door lock mechanism, hinges and window rubbers as these can cause creaks from time to time.

Nov 13, 2012 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

759 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...