Question about 1991 Dodge Ram 350

1 Answer

1991 dodge power ram 350 brake failure

Soft brake peddle, bled the brakes, changed the master and still wont pump up

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Look For some kind of leak

Posted on Nov 27, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BCally1
  • 133 Answers

SOURCE: 2007 Dodge Ram 2500 - Brake peddle wobbling

only comes as a whole pedal assembly. not to hard to change out though just takes a little while if its your first one

Posted on May 21, 2009

yotaguy
  • 232 Answers

SOURCE: Brake peddle goes to the floor intermitantly.

The problem may be that the master cylinder needs to be bench bled,there is most likely air trapped in the piston of the master cylinder.The problem comes from the piston not being fully actuated when connected to the pedal assembly.A vacuum bleeder will generally pull it out.

Posted on May 25, 2009

tpllima88
  • 35 Answers

SOURCE: 1988 DOdge Ram 350 van wont fire or start?

first is first check battery and alternator

Posted on Feb 24, 2010

Tim Owyang
  • 23 Answers

SOURCE: 2001 RAM 2500 Brake Pedal Goes to Floor

Excessive runout or wobble in a disc (Rotor) can increase pedal travel due to piston knockback and increase piston seal wear due to necessity of caliper to follow disc wobble. Thickness variation in a disc can also result in pedal pulsation, chatter and surge due to variation in brake output when disc section is uneven. Dishing or distortion can be caused by extreme heat and abuse of the brakes. Hope this helps, Good luck.

Posted on Apr 09, 2010

bsdracing
  • 57 Answers

SOURCE: I have a 2001 Dodge Ram 2500 5.9 Cummins Diesel No Brake Pedal

what it sounds like to me and I pretty much only work on cummins and powerstroke trucks. your problem seems that your calipers are worn and are not holding the pressure. and or the lines going to them have faded and caused them to ballon or stretch. if the pedal is vary hard to puch hydraboost and worn parts but if the pedal isnt hard then your hydrabosst should be fine as i said most likley your rubber brake lines in front and worn calipers

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 GMC Duramax i installed a new master cyclinder my brakes hold untill i start my truck then they go to the floor


Bleed the brake system, You should have bled the master cyl on the bench before installation..

May 12, 2014 | 1991 GMC G3500

1 Answer

How to change brake booster and leave master cylinder? 350 engine


Unbolt, master cylinder from booster, the brake lines from the master cylinder, will flex enough to where you can put it over to the side, where you would be able to remove the booster.Then unbolt the 4 bolts under the dash and unhook linkage to brake peddle.

Jul 23, 2010 | 1991 Chevrolet K1500

1 Answer

When push brakes you have to push really hard to make them go in then the truck barely stops. Replaced the MC and bled the brakes now every time push brakes truck acts like its going to die. Brake light...


Sounds like you will have to bleed your brakes again, but thats not the problem og hard brake peddle, need to check your power brake booster, sit right in back of master cylinder, check make sure it has vacum going to it, also to test it with engine off, press on brake peddle three time, then state engine with foot on peddle, peddle should go down a few inches, also with engine of peddle should feel soft for three pumps, if you have none of this , power brake booster is bad.

Jul 04, 2010 | 1995 Toyota 4Runner

1 Answer

2001 Chev blazer, brakes have been bled, peddle


You probably have air between the master cylinder and the abs pump. Fill the reservior and have someone pump the brake and bleed the primary lines at the abs pump. Good luck.

Apr 19, 2010 | 2001 Chevrolet Blazer

3 Answers

Brake peddle goes to the floor intermitantly.


The problem may be that the master cylinder needs to be bench bled,there is most likely air trapped in the piston of the master cylinder.The problem comes from the piston not being fully actuated when connected to the pedal assembly.A vacuum bleeder will generally pull it out.

May 25, 2009 | 2004 Dodge Ram 2500

3 Answers

Brakes are still spongy after changing the pads, one caliper, and master cylinder. bled front brakes.


I just went to Brake Masters this morning and had them replace the Master Cylinder since I was experiencing the pedal very spongy and going to the floor. When they replaced the Master Cylinder and they gave me back the car, the brakes were still spongy and going to the floor. I addressed this to them and they took another look at it, but when I took it for a second time, the brakes were extremely spongy. It was almost like they gave me back my car in worst condition to when I brought it in. Can you help?

May 21, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

No brake pressure


The master brake has gone totally bad

May 21, 2009 | 1992 Oldsmobile Ninety Eight Regency

2 Answers

Brake pedal goes to floor after bleeding the brakes many times


start off by pumping the peddle 25 times with engine off ... bleed the abs system (usually has bleeder valves near/on control unit). then bleed the rest as usual with engine off ... DO NOT turn the key on while bleeding abs brakes.

Mar 18, 2009 | 2000 Dodge Caravan

1 Answer

Keep geting air in the back Brake


you need to have someone pump the pedal until you have a steady stream of fluid.and start at the furtherst point from the master cylinder and work forward.

Jan 16, 2009 | 1996 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...