Question about 2004 Ford Fusion

Open Question

Ford fusion override button picture - 2004 Ford Fusion

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace belt in a 08 ford fusion


Anon, Take a picture of belt routing before you start as you may forget how to route belt when putting new one on. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
changing the serp belt 2 3L 2 5L
HOW TO REPLACE SERPENTINE BELT
How To Change Serpentine Drive Belt Ford Focus

Jun 01, 2016 | 2008 Ford Fusion

1 Answer

Where is the break safety switch located in a 2009 Ford Fusion


Jeanette, break switch is above brake pedal arm, safety neutral switch is on transmission, clutch pedal safety switch above clutch pedal arm. Links below have pics.
to show your appreciation press the helpful button and follow me on fixya for more tips and info.

06 ford fusion brake light switch replace

How To Test and Replace the Neutral Safety Swtich Inhibitor Switch P0705

Clutch switch behind clutch pedal Ford Focus Forum Ford Focus ST Forum...

Replace master cylinder clutch Ford Focus Forum Ford Focus ST Forum Ford...

Feb 15, 2016 | 2009 Ford Fusion

1 Answer

When I turn the ignition off the average fuel reading returns to zero,all other readings,tripometer,miles to empty remain.


2006 Ford Fusion Owners Manual - Scribd

https://www.scribd.com/doc/.../2006-Ford-Fusion-Owners-Manual
Mar 10, 2014 - 2006 Ford Fusion Owners Manual - Ebook download as PDF File (.pdf), Text ... To reset the switch, refer to the Fuel pump shut-off switch in the .... Holding the TRIP/RESET button for two seconds or more will reset the trip odometer to zero. .....Turn the ignition switch to RUN and then back to LOCK. rotate the ...

[PDF]Ford Fusion - Dealer e-Process

cdn.dealereprocess.com/cdn/servicemanuals/ford/2006-fusion.pdf
2006 Fusion (fsn) ... well acquainted with your vehicle by reading this handbook. ...Fuel pump shut-off switch: In the event of an accident the ..... reset the trip odometer tozero. ..... Turn the ignition switch to RUN and then back to LOCK. 4.

Nov 24, 2015 | 2006 Ford Fusion

3 Answers

2009 fusion SEL has data compass error after being rear ended and a shop did repair.


WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION ...

www.fixya.com/cars/t16705785-compass_error_2009_ford_fusion
Feb 21, 2013 - WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION A MESSAGE COMES UP ON MY DASH SAYS COMPASS NO ... SOURCE: I HAVE A2009 FORD FUSION AND IT'S NOT GOING OVER 20 MPH ... Compass data error -- how do i determine my zone-- ... Jan 28, 2010 ' 2007 Ford Edge SEL Plus.

Compass - Ford Fusion Sport - Ford Fusion Forum

www.fordfusionforum.com/topic/9390-compass/
Jan 23, 2013 - Compass - posted in Ford Fusion Sport: 2011 Fusion SEL without navigation screen. Following windshield ... I have recalibrated and reset the compassaccording to the manual instructions (several times) but cannot correct the error. Can anyone help? ... picture of where it is: 2009-08-30_051718_2.gif.

Nov 08, 2015 | 2009 Ford Fusion

1 Answer

My ford fusion went into idle mode after it was stuck in snow. How do i override that?


Consult your local ford garage and ask the shop manager how to clear and reset the main computer.

Feb 15, 2015 | 2013 Ford Fusion

1 Answer

Interlock sensor Ford Fusion, Key Stuck


Do the brake lights work ?
Diagnostic Trouble Code (DTC) Chart
DTC Component Description Condition Symptom Action B2572 Brake Shift Interlock Brake Shift Interlock Output Circuit Failure The associated circuitry connected to the smart junction box (SJB) or fuse, or the SJB itself may have an issue causing a brake shift interlock concern. Brake shift interlock is inoperative or does not operate correctly. Go To Pinpoint Test A .

May 20, 2017 | 2007 Ford Fusion V6

1 Answer

2006 Mercury Milan key stuck in ignition.


There's a TSB published by ford for this condition. It's caused by a binding shifter button.


adobe.gif Printable View (73 KB) TSB
07-14-7
  • KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION
Publication Date: July 6, 2007
FORD: 2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan
This article supersedes TSB 07-2-1 to update the Part List. ISSUE: Some 2006-2007 Fusion, Milan and 2006 Zephyr vehicles built before 9/4/2006 may exhibit a customer concern of the ignition key getting trapped or a shifter slider binding condition. Most of the key trapped conditions are caused due to a binding shifter button which does not allow the pawl to contact the park detect switch.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE If the key will not release from the ignition cylinder lock follow the Key Trapped procedure. On vehicles with a hard-to-shift shift lever into park or slider bunching/binding then follow the Shifter Slider Binding procedure. Key Trapped:
  1. Actuate knob button 5-10 times, observe for binding or sticky condition.
  2. Replace knob assembly if the knob sticks following Workshop Manual (WSM), Section 307-05. NOTE: WHEN REPLACING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR.
Shifter Slider Binding:
  1. If shifter slider is bunched up or binding, replace bezel assembly following WSM, Section 307-05. NOTE: WHEN REPLACING THE BEZEL, CARE NEEDS TO BE TAKEN TO ENSURE THAT THE BRAKE SHIFT INTERLOCK OVERRIDE TAB IS PROPERLY ALIGNED INTO ITS GUIDE. REFER TO FIGURE 1.

    tb8706a.gif
    Figure 1 - Article 07-14-7

    NOTE: WHEN REINSTALLING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR. NOTE: IF OVERRIDE CAP IS DAMAGED DURING REPAIR, IT IS AVAILABLE SEPARATELY.

PART NUMBER PART NAME 6E5Z-7D443-B Bezel Asy-Black w/FNR5 Trans (Fusion-Milan) 6E5Z-7D443-C Bezel Asy-Black w/Aisin F21 Trans (Fusion-Milan) 6H6Z-7D443-A Bezel Asy-Satin Nickel (Zephyr) 6E5Z-7213-C Knob Asy-Black (Fusion-Milan) 6H6Z-7213-A Knob Asy-Charcoal (Zephyr) 6H6Z-7213-B Knob Asy-Charcoal-OD (Zephyr) 6E5Z-7A214-B Override Cap-Black (Fusion-Milan) 6H6Z-7A214-A Override Cap-Satin Nickel (Zephyr) W790088-S901 Screw (2 Req)
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION DESCRIPTION TIME 071407A 2006-2007 Fusion, Milan And 2006 Zephyr: Replace Knob Assembly, Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.3 Hr. 071407B 2006-2007 Fusion, Milan and 2006 Zephyr: Replace Bezel Assembly Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.4 Hr.
DEALER CODING BASIC PART NO. CONDITION CODE 7213 69

NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.

Copyright © 2007 Ford Motor Company
2010&c18=non-tab%20view&c21=07-14-07&c35=tsb%2c07-14-07&s=1366x768&c=32&j=1.3&v=y&k=y&bw=778&bh=347&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 2006 Mercury Milan

1 Answer

I have a 2008 ford fusion along with 2002 ford taurus. Just for the testing purposes I was trying to program the taurus keyless remote into the fusion, and now the single keyless remote is working on both...


cycle your ignition 8 times on and off really fast then on the eight time you cycle the door locks should lock and unlock,then hit the lock and unlock button on your fob that should set it just for one car. if you try to reset the fusion key your dealer will charge you alot of money

Sep 26, 2010 | 2008 Ford Fusion

1 Answer

Can't remove my key


not sure some Ford u have to push in a button to remove the key . Check and see if the model has that.

Jul 09, 2009 | 2007 Ford Fusion I4 SEL Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...