Question about Cars & Trucks

1 Answer

Hi my bmw 320d not starting

I was changing cylinder head i set timing correctly but its doen't want to start what can i do now

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 818 Answers

Are you getting fuel and spark-pull a plug and see if its wet from fuel- ground it out and see if its sparking- cheers Denny

Posted on Nov 27, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
grease16
  • 58 Answers

SOURCE: How do I change the brake pads on my BMW 320d E46

pull off the wheels than than pull the brake pad housing away from the rotor

Posted on Jun 30, 2008

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

steve_e_uk
  • 1675 Answers

SOURCE: CYLINDER HEAD TORQUE SETTINGS BMW 318TI THANKS

hi this has to be done in 3 stages, leaving 20 to 30 minutes between tightening's they are as follows..
stage 1: 30Nm leave 30 minutes stage 2: 90 degrees turn leave 20 minutes stage 3: 90 degrees turn leave 20 minutes
you have to leave them this length of time so as not to put to much strain on the head in one go...hope this helps please vote thanks

Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BMW 320d e46 cranks but won't start.


check the cylinders compression, if below to 95 psi remove the spark plugs then check if wet with fuel ,
if this condition exist , It is very possible that you have to recondition the pistons, rings or cylinders

May 24, 2017 | BMW Cars & Trucks

1 Answer

Power going through to the injectors but the car wont start


If you have fuel to the cylinders and its not even trying to start you most likely have no spark ! Possible timing belt broke

May 08, 2016 | BMW 320D Cars & Trucks

1 Answer

What is the tank capacity on a bmw 3 series 320d


60 litres

BMW 3 Series 320d Specifications - Drivespark.com www.drivespark.com > Cars > BMW > BMW 3 Series BMW 3 Series 320d price starts at Rs. 33.65 lakh in India. ... Fuel Tank Capacity 60 litres: Mileage (ARAI ... Choose Other BMW 3 Series Variant

Apr 09, 2016 | BMW Cars & Trucks

1 Answer

My 2004 bmw 320d touring white smokes when idle,and realy white smokes when driving.runs fine no loss of power.


Coolant is getting into one of the cylinders of engine , head gasket , a crack in the cylinder head or engine block !

Jul 14, 2015 | 2004 BMW 320d Touring

1 Answer

I have a bmw e46 320d 4 cylinders the car doesn't start in cold I changed the cold start plugs and it still doesn't start


the plugs work from current from a relay . did you check all the fuses and the relay.

Oct 30, 2013 | BMW Cars & Trucks

1 Answer

Where are the timing marks on a bmw 320d e46?


make sure the distributor is firing on number 1 cylinder then determine tdc of number 1

Aug 04, 2012 | BMW 320D Cars & Trucks

1 Answer

Clock


hi..

put your keys in so that your instrument clsuter on the dash come on,(no need to start the engine), use your mileage reset button to change time by turning it clockwise and anticlockwise till you reach the correct time.. it will change on your dash aswell as your radio..

Jan 05, 2009 | 2005 BMW 3 Series

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...