Question about Cars & Trucks

Open Question

2009 isuzu dmax wiring diagram - Cars & Trucks

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 96 Answers

SOURCE: 1998 Hombre: factory stereo wiring diagram for 1998 isuzu hombr...

Try http://www.helminc.com. It should be available on Print on Demand.

Posted on Jul 22, 2010

  • 6982 Answers

SOURCE: my isuzu dmax oil pan

In order for that dent to have any real effect upon oil delivery, the dent would need to be perfectly flat up against the oil pump pickup. Chances are it isn't. The pickup in most pans is located a bit above the pan bottom to lessen the chance of ingesting any contaminants (sand, grit, hard carbon etc). With the clearance diminished, chances of that are greater.
While only oil pressure is measured, volume is also important. With the pan that close to the pickup, pressure probably won't be a problem but you may loose some volume (impossible to tell how much).
When I put together a fresh engine, I like to see pressure of about 40psi or better. As an engine wears, engineers claim that anything above 15psi is OK...I use a higher number of 25psi (at idle) as a minimum "safe" limit. Anything below that, you know you have a problem and it's wise to find it early and fix it. (Pumps rarely fail...most low pressure problems can be traced to engine bearing wear, resulting in bleed off past the bearings)
As for your pan: If the pan is bent, and you have it off the engine, why not hammer the bend out a little? or, better yet, get another pan from a scrapyard and replace it entirely?
If you have not removed it, there's no real way of measuring and what you are seeing may not be the whole story...pickup clearance may be greater elsewhere. In that case, just continue doing regular service and save pan replacement for a day when you have time to do it.

Posted on Mar 30, 2011

headstrong56
  • 493 Answers

SOURCE: isuzu DMAX sudden power loss

could be fuel filter clog.air filter or MAP sensor or an intermittent speed sensor on the transmission

Posted on Jul 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Isuzu dmax 2006 model 4x4 automatic transmission, the check trans is flashing


problem probably in the wiring harness and connections
next have the fault codes read to pinpoint the problem area

Aug 05, 2016 | Isuzu Cars & Trucks

1 Answer

2013 Isuzu D-max valve clearances?


what car , Dmax
what engine? they have many engine choices world wide...
what country,

Jul 28, 2016 | Isuzu Cars & Trucks

1 Answer

DMAX 4 wheel drive utility. How do I remove the plate lamp?


wow no year car stated or country. 2002 to PRESENT.
is car outside, USA ?we dont have books on DMAX here.

license plate lamps.
on our cars the operators guide in the glove box covers this, turn to Bulbs page and its there. get the guide, never lose it.

13 DMAX assembly plants world wide, and most are not the same.
(laws in your country all dictate light rules, most)

see?

Jul 16, 2015 | Isuzu Cars & Trucks

1 Answer

Isuzu dmax has got a problem it starts but produces a thick white smoke and cant accelerate hence no power!kindly help!


check the oil dip stick to see if water has got in to the oil, if it has the oil will be a light brown ish colour, and if so then I am afraid you have blown the head gasket (Not a cheap fix sorry)

Sep 30, 2014 | Cars & Trucks

1 Answer

Want to know where to conect blue and black wire on isuzu dmax gearboks


If there only two wires then check the blue one for power and if so then the wires will probably go on the reversing switch

Dec 29, 2013 | Isuzu Rodeo Cars & Trucks

1 Answer

Where can i get rid of a brand new Isuzu DMax tub


I am looking for a Isuzu dmax tub ,, contact number 0419264083

Mar 14, 2013 | Isuzu Pickup Cars & Trucks

1 Answer

Isuzu DMAX sudden power loss


could be fuel filter clog.air filter or MAP sensor or an intermittent speed sensor on the transmission

Jul 13, 2012 | Isuzu Cars & Trucks

1 Answer

First this isuzu dmax just stop suddenly,i clean the fuel filter then clean the cencor in the tank,then the cencor connceted to the pump then it manage to start and idle properly but the engine check


to whom it may concern. my dmax model 2006 3000 cc lately having problem like engine suddenly stop especially when it slow,fuel filter already new fuel line been check but the problem still there.anyone been encountered this problem before what is the problem?

Jul 01, 2012 | Isuzu i-280 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...