Question about Cars & Trucks

1 Answer

Chevrolet wiring diagrams

Instrument cluster panel not workin

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

All wiring diagrams can b purchased on the 'net...some may be seen free, or purchase a repair manual...

Posted on Nov 27, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 48 Answers

SOURCE: 1995 Neon Instrument Cluster Wiring Diagram

are you talking about the wires that connect the car harness to the gauge cluster with the 2 big plugs?

Posted on Jul 17, 2008

alicantecoli
  • 22095 Answers

SOURCE: Why is not there a VW Polo 6N listed?

if warning light control not working change the altenator

Posted on Feb 22, 2009

  • 48 Answers

SOURCE: 2000 Chrysler Voyager Instrument Cluster is dead

have you got a dimmer switch on your model to dim the dash lights. if you have it may be faulty. link the cables together if the lights work the switch is faulty. if you have not got a dimmer switch
your printed circuit on the back of the dash may be faulty or the plug in the back of the dash is not pushed all the way in. hope this helps

Posted on Apr 16, 2009

  • 1 Answer

SOURCE: instrument panel cluster gauges and odometer has stopped working

I had all my analog instrument panel gauges stop working after they did the state emissions test. I found the proper fuse in the fuse block located under the hood. Simply unplugged the fuse, noticed it was still good, and plugged the same fuse (10A) back in and all the gauges started working again. Guess it needed a reset atfer they plugged in for the emissions.

Posted on Aug 14, 2009

wiringlunati
  • 576 Answers

SOURCE: instrument cluster bulb is out. how do i replace

It may not be a bulb, as the instrument cluster usually has a number of bulbs and they probably didn't all blow at once. Pulling instrument clusters can be touchy and may not be for the average "shadetree mechanic" however, typically there are a few screws above the cluster going into the dash pad and a few hidden behind the trim panels below the cluster.

Posted on Dec 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 gmc envoy instrument cluster panel wiring diagram


https://s15.postimg.org/taongnt97/Untitled.jpg

Click on the link, hope it works?
Yes, it is a partial diagram. Check voltage and ground, see the fuses, not only check the fuses, check the fuse circuit for voltage. Use a test light. Some fuse circuits are hot all the time, some go hot with the key on. Also, check the ground, black wire with white tracer in diagram, should be chassis ground, check the way you would any chassis ground.
Any applicable trouble codes? As far as your gages, the pcm sends serial data to instrument cluster telling ipc what to do with gages. I can't rule out instrument cluster itself, at the moment.

Feb 14, 2017 | 2003 GMC Envoy

1 Answer

I have an 01 Pontiac Azteca the problem is everytime I put the car in gear it shuts the dash lights and radio light off, any idea what could cause this?


A bad or lose ground ! Checking a wiring diagram would show if these thing's share a common ground . Transmission , instrument cluster lighting an the radio lights up with the instrument cluster . You can go onto youtube an check out videos on how to read a wiring diagram , how to do voltage drop testing , basic automotive electrical circuit testing . Then you could go to http://bbbind.com/free_tsb.html free wiring diagrams an test the instrument panel back lighting circuits ! You will need a DVOM - digital volt ohm meter an you will more then likely need to take parts of your instrument panel apart . Your probably better off taking your vehicle to a qualified repair shop .

Aug 04, 2016 | Pontiac Cars & Trucks

1 Answer

Why don't instrument panel gauges work?


cluster is probly bad causing heavy amp draw--remove instrument cluster/panel and have it refurbished at napa------wiring or module could also be bad in the harness-inspec it 1st bfore doin anything

Sep 08, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

Dash wireing diagram speedometer don't work


gm vehicles have alot of problems with the motors that run speedometer you can get instrument clusters at Murray's it is that common most instrument clusters are dealer only but these fail that much you can get them aftermarket.

Dec 15, 2010 | 2004 Chevrolet Silverado 3500

1 Answer

Speedometer no workin trailblazer 2005


Pretty common problem with these. Here's a guide to learn how to fix GM instrument clusters yourself, I used it to fix mine and it worked great. How to guide for Trailblazer instrument cluster repair

Jun 15, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Headlight swicht broke


Removal & Installation
  1. Disconnect the negative battery cable from the battery.
  2. Remove the lower steering column cover-to-instrument panel screws and the cover.
  3. Remove the instrument cluster trim plate-to-instrument cluster screws and the panel, then allow the panel to hang to the left side by the wiring.
  4. Disconnect the electrical connector from the rear of the headlight switch.
  5. Disengage and remove the headlight switch from the instrument cluster trim plate.
To install:
  1. Connect the electrical connector to the rear of the headlight switch.
  2. Engage and install the headlight switch in the instrument cluster trim plate.
  3. Install the instrument cluster trim plate-to-instrument cluster screws and the panel.
  4. Install the lower steering column cover-to-instrument panel screws and the cover.
  5. Connect the negative battery cable to the battery and check operation.

Apr 27, 2010 | 1995 Chevrolet Astro

4 Answers

Heated seats not working, heater not heating, speedometer not working.


sign up @ autoZone.com and add your car to your account "repair info, vehicle repair guides, then wiring diagrams. They have the diagrams for the heated seats

Dec 08, 2009 | 2004 Cadillac Escalade Esv

3 Answers

Speedometer just stopped workin its like 180 is actually o km/h and then it wont go down past 180


Hi. There is a speed sensor mounted on the transmission. Check the wires that lead from the sensor to the instrument cluster in your dash. Make sure the speedometer is connected to the sensor, and the connection is not loose. If the wiring at the sensor, and speedometer are ok, simply replace the speed sensor.

Nov 13, 2009 | 2005 Chevrolet Silverado

3 Answers

Instrument cluster does not work except oil pressure and voltage


I actually had the exact same thing happen to my 2001 Silverado and I bought an instrument cluster too. It was the 10A radio fuse in the fuse panel beside the dash. It was not pushed in all the way.

Aug 06, 2009 | 2001 Chevrolet S-10

1 Answer

86 IROC heater core


Removal & Installation
1.Disconnect negative battery cable. Drain cooling system. Disconnect heater hoses from heater core, and plug openings. Detach hood release cable. Remove both dash side panels. Remove left and right lower dash trim panels. Remove glove box. Remove 7 screws securing center accessory console. Disconnect wires on accessory console, and remove accessory console. Remove control cables at heater case.

2.Remove 4 bolts securing steering column to instrument panel. Lower steering column. Remove 2 bolts from instrument panel mounts at far left and right sides of instrument panel. Remove defroster duct trim on top of dash. Remove instrument cluster screws. Pull instrument cluster out slightly. Disconnect electrical connections and speedometer cable from instrument cluster. Remove instrument cluster.

3.Disconnect all electrical connectors from instrument panel. Remove parking brake console. Remove glove box. Remove bolts securing instrument panel support to floorpan. Remove all instrument panel mounting bolts. Remove instrument panel.

4.Separate heater case from blower. Remove 3 nuts and pull heater

Dec 06, 2008 | 1986 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...