Question about 2004 Infiniti QX4

Open Question

Bolt sequence for 2001 infinity QX4 oil pan - 2004 Infiniti QX4

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bibleman01
  • 334 Answers

SOURCE: 2001 Infiniti QX4 low beam bulb replacement instructions

Look directly behind the headlight box if there is a rubber sleave covering the plug take it off. Unplug the wires from the bulb, there may be a saftey clip you will have to pry up to get it off.after you get the plug off the bulb holder should twist counterclockwise then it will pull right off.When you change the bulb just remember to wipe your body oil off the bulb before attaching it back into the headlight box. Then plug it back in and your in business. The high beam has three wires and the low beam has two wires. The bulb will have to be the right one.
God Bless You Greg

Posted on Nov 25, 2008

  • 1 Answer

SOURCE: Sunroof on Infinity QX4 (2001)

Good news I found out from a forum and it worked for me. Here it is

: 2002 pathfinder sunroof acts up after replacing battery (CKirbyjr) 5:30 PM 5/9/2008 qt.gif reply.gif edit.gif

Welcome to NICO -- The same thing happens whenever I disconnect my battery.
Try opening the sunroof all the way (2 inches at a time) and then close it (again two inches at a time). Turn the vehicle off and on again. Sunroof should operate normally.
I'm not sure if the last step is required but I've always done it anyway. It's worked all three times I've had my battery disconnected.

Posted on May 15, 2009

pingman37
  • 58 Answers

SOURCE: MY 2001 INFINITI QX4 KEEPS SAYING SERVICE SOON

First off, make sure that the gas cap is tightened beyond three clicks. If it is and has been then there are many things that could be causing the light to come on. But let me start by assuring you that it is not something that requires immediate attention. The sole purpose of the service engine light is to detect malfunctions of emissions related components. If the gas cap isn't tight, the computer system detects an incorrect amount of pressure inside the tank due to vapor leaking out of the filler neck. If the cap is tightened after a period of time the computer detects the right pressure and the light will go off. However, on QX4's the most common cause of the light is oxygen sensors, or cam and crank position sensors, and finally intake valve timing control sensors or solenoids. O2 sensors measure the amount of oxygen in the exhaust gas. Normally I have seen that in damp and wet conditions these sensors are more likely to intermittenly give false readings. That being said, although the SES light is not an emergency situation, it will need to be addressed at some point, as the Engine control module takes the readings from these various sensors and automatically adjusts things like idle control, and air fuel mixture ratio, and eventually will to some point affect the performance of the vehicle. I have seen folks drive 100K miles with a service engine light on, so if you don't want to spend a 200 or so dollars right away, I would take the car to autozone, have the codes retrieved, and report back to this forum, at that point I would be able to advise you a little further. But more than likely you could continue driving the car without any driveablility issues.

Posted on Jun 16, 2009

  • 5 Answers

SOURCE: how much oil does the 1999 infiniti qx4 hold (when

5 quarts

Posted on Aug 06, 2009

  • 312 Answers

SOURCE: Pls where is Swirl Control Solenoid Valve located in Infiniti QX4

This link shows the location of the SCV, If your motor is different the location should be similiar. http://img510.imageshack.us/img510/5687/vacuumdiagramuh3.jpg

There's a vaccuum line that runs off the SCV to the SCV check switch.

P0442: Have you inspected the lines, charcoal cannister etc? Make sure the fuel cap is tight. The easiest way to check the system is to have someone perform a smoke test. I had a DTC on my car which indicated a EVAP problem, it turned out to be the Fuel tank evaporator Control Solenoid.

Posted on Sep 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset service engine soon light on 2002 Infiniti QX4?


Here's a YouTube video to reset the reminder on the Infiniti/Nissan.
Nissan Infiniti oil service reset

Nov 08, 2016 | 2002 Infiniti QX4

1 Answer

Where is the torque converter clutch solenoid?


The torque converter is inside the transmission. The (electric) clutch solenoid - usually - is on the outside of the transmission case.

Get a flashlight, get under the vehicle and look on the transmission case for electrical wires..

The link below will give you a general idea of what it may look like:

Transmission Control SolenoidsFor Infiniti J30 M30 Q45 and QX4

Feb 24, 2016 | 2001 Infiniti QX4

1 Answer

Change oil pan on a 2001 sonoma


the 2.2 engine and the 4.3 engine with 2WD MODEL you have to remove engine.the 4WD MODELS, you have to remove all these parts first remove dip stick, drive belt, splash shield, remove front axle shield and the transfer case shield, front skid plate and the flywheel cover,remove left and right engine mount through bolts.then raise the engine using a lifting device, and block in position,using large wooden blocks between the motor mounts and brackets.you will also need to remove these parts,remove disconnect oil cooler line, remove pitman aem bolt and pitman arm, remove idler arm bolts and idler arm, remove front differential through bolts,remove front driveshaft if necessary,remove differential assembly by rolling it forward for clearance, remove starter motor, then remove oil pan bolts then remove oil pan, your oil pan need to be flushed slightly forward of rear of the block to allow proper alignment with the transmission housing.using feeler gauge measure the 3 oil pan to transmission contact points.clearance should not exceed 0.011 in. 0.3mm if so realign the oil pan.oil pan bolts torque is 18 ft lbs tighten oil pan bolts in sequence.

Aug 25, 2012 | Cars & Trucks

2 Answers

I am replacing the oil pan gasket and the bolt diagram doesnt match the gasket we are putting on the car. I need the tightening order for the 2000 ford taurus lx with ohv. please and thanks!


OKAY LOOKING AT OIL PAN FACING SHALLOW END LEFT SIDE STUDS BOLTS SEQUENCE 13 12 11 10 9 BACK BOLTS 8 7 6 5 OKAY 5 BOLTS WILL BE ONE OF THE RIGHT SIDE STUDS STARTING AT 5 BACK STUD THEN BOLT 4 3 2 1 AND FRONT BOLTS ON FRONT OF PAN AFTER 1 BOLT 15 AND BOLT 14. SEE FRONT BOLTS ON FRONT END OF OIL PAN 14 15 AND 1. WRITE NUMBERS DOWN IN THE SEQUENCE I GAVE YOU ON PAPER. DRAW OIL PAN ROUGH DRAFT PUT THE NUMBERS I GAVE YOU I SAME SEQUENCE THATS YOUR OIL PAN BOLTS SEQUENCE.

Apr 18, 2011 | 2000 Ford Taurus

1 Answer

Need diagram for 2000 ford taurus oilpan


Oil Pan - Removal & Installation3.0L Engine
VIN S Engine
  1. Before servicing the vehicle.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Dual converter Y-pipe Transaxle support bracket Oil pan by following the bolt removal sequence shown

    8d11698.jpg
    Fig. Oil pan bolt removal sequence-2000-04 3.0L (VIN S) engine


    2272e92.jpg
    Fig. Oil pan bolt tightening sequence-2000-04 3.0L (VIN S) engine
Hope helps (remember rated and comment this).

Aug 15, 2010 | 2000 Ford Taurus

1 Answer

Where is the top oil pan located in the 2003 nissan altima 3.5? Need a diagram. This car has 2 oil pans.


Aluminum (upper) oil pan bolt loosening sequence—3.5L engine



dac3faf.gif

Position a suitable jack under the transaxle.
  • Crankshaft Position (CKP) sensors (REFERENCE and POSITION) from the oil pan
  • Front and rear engine mounting nuts and bolts
  • Center crossmember assembly
  • Engine drive belts
  • A/C compressor and mounting bracket
  • Rear cover plate and the lower transaxle bolts
  • Aluminum (upper) oil pan bolts in the reverse of the installation sequence

May 23, 2010 | 2003 Nissan Altima

1 Answer

How can i get the oil pan out on a 2001 chevy malibu?


2.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan


  1. Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm).
  2. Accessory drive belt
  3. Negative battery cable

  4. Fill the engine with oil to the correct level.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan

To install:
  1. Apply a 0.13 inch (3.5mm) bead of the GM P/N 12378521 sealant around the perimeter of the oil pan and oil suction port opening.
  2. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).

    0900c1528024bb26.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Oil pan bolt sequence-2.2L engine
    Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm). Accessory drive belt Negative battery cable
  3. Fill the engine with oil to the correct level.
3.1L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Evacuate and recover the A/C system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    WARNING DO NOT disconnect the refrigerant lines or allow the compressor to hang unsupported.


    Negative battery cable Accessory drive belt Upper and lower radiator hoses Right front wheel Inner fender splash shield Antilock Brake System (ABS) Wheel Speed Sensor (WSS) electrical connector Right front ball joint from the steering knuckle Right side outer tie rod end A/C compressor bolts and move the compressor aside


    Evaporator-to-accumulator A/C line Flywheel cover Engine cradle bolts Crankshaft balancer Starter motor Oil pan

To install:

0900c1528024bb27.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the oil pan mounting-3.1L and 3.5L engines

  1. Install or connect the following:

Sep 02, 2009 | 2001 Chevrolet Malibu

1 Answer

How many catalitic converters are on the 2001 infiniti QX4


There are only to Catalysts monitored by the ECM. There is a wide pipe near the front of the exhaust system that looks like it houses a catalyst, but it doesn't. Look for the rear O2 sensor, that is where the catalyst is. If the bolts that hold it on are not badly rusted, and depending on your mechanical aptitude you could replace them, otherwise take it to a shop. Have you checked the warranty coverage with the dealership?

Oct 28, 2008 | 2004 Infiniti QX4

Not finding what you are looking for?
2004 Infiniti QX4 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...