Question about Cars & Trucks

1 Answer

How to replace clutch

Daihatsu Sirion 1.3 16V 2002 CLUTCH REPLACEMENT METHOD

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Man, u jus gotta purchase a repair manual for $30!!...don't know y people r so reluctant about purchasing a repair manual!! always get ur money back usually on the 1st repair job!! a repair manual for $30 or pay the garage $300 or more!!

Posted on Nov 27, 2013


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


SOURCE: Daihatsu Sirion

I assume you are changing the timing belt. I am a mechanic and although not familiar with your vehicle, you would usually locate the timing mark on the bottom pulley and line this up. Careful not to turn the engine over too hard as pistons can strike valves. then you should look for similar marks on the camshaft pulley[s], and line these up. Then fit belt. This has to be tensiond correctly which is important. Hope this helps. Mike the bike01.

Posted on Aug 19, 2008

  • 98 Answers

SOURCE: 1999 Daihatsu Sirion

Your engine is probably an EJ-DE twin cam 12 valve.

Generally Daihatsu belts have marks on them that line up with dimples on the sprockets for the intial phasing. You rotate the engine to top dead centre on No1 piston and install the belt from there. The cams should be not be putting any pressure on the intake and exhaust valves of No1 when phased correctly.

Posted on Oct 10, 2008

  • 67 Answers


you can buy a puller kit for the AC clutch for about $35.00 the bearing is about $25.00 you might be able to do it without removing it from the engine saving your freon.
Belt tensioners just unscrew.They are also inexpensive

Posted on Apr 13, 2009

  • 1 Answer

SOURCE: kia clutch replacement

have 2004 optima and the trans axel wont seperate from motor

Posted on Mar 10, 2010

  • 1 Answer

SOURCE: Honda Crv 2002 a/c clutch replacement

I had a 2002 Honda CRV , the problem have noise when in/out release clutch after two years , I send to dealer in 2003 and 2007 ,
now the noise is more before and make me so unconforteble but dealer said that will not causing any faults . any one know why they don't response it ? .

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Gearbox not doing reverse and Now just revving after Gear 2

Sorry to tell you that you have a failed transmission and it will need to be rebuild or replaced.

Jun 28, 2016 | 2005 Daihatsu Sirion 1.3

1 Answer

What dos vvt system malfunction it mean ?

Variable Valve Timing System Malfunction, and possible causes - dirty or low engine oil
- Valve timing
- Oil control valve
- Variable Valve Timing controller assembly
- Engine Control Module (ECM)

Read more:

Jul 27, 2014 | 1999 Daihatsu Sirion

1 Answer

How do you to replace a headlight bulb on Daihatsu Sirion 2007?

go to an autoparts store and ask them what bulb it takes then ask them how to change it . ,ost any more you remove them from under the hood by twisting and pulling out .

Jul 06, 2014 | 1998 Daihatsu Sirion

1 Answer

How do i replace bulb in headlight of 2006 daihatsu sirion

from inside the motor compartment .any auto parts store can show you how .

Jun 19, 2014 | 2006 Daihatsu Sirion 1.3

3 Answers

Is replacement of 2007 Daihatsu Sirion 1.3 fanbelt a relatively simple task or is it for a professional mechanic only?

DO IT YOURSELF... It IS fiddly but perfectly do-able.. easiest way to do it is to remove plastic 'dirt shield' from driver's side inner wing (next to drive shaft and brake line) obviously wheel removed, or rotated is ok.. removal of modern plastic 'tat' is simple (area of cylinder head) allowing as much finger access as possible..not much room down the side of these puppies!! Next you need to de-tension the 'serpentine' belt BUT I WOULD RECOMEND DRAWING BELT & PULLEY SET UP FIRST or taking several photos.. as a reminder of if belt goes over or under (makes sense when you see it) Use blunt engineer's screwdriver (or any blunt long driver, rod, etc) to help push and pull old and new belt about.. REMEMBER TO RE-TENSION THE TENSIONING PULLEY...BUT DONT OVER DO IT!! THE BELT WILL TIGHTEN EVEN MORE AFTER SHORT RUN IN.. ALLOW SLIGHT DEFLECTION.. 6 to 10mm should do... cleanliness is the key really, as with all engine jobs(!) Allow 2hrs to do... if you've never done before... ok?

Mar 04, 2013 | 2007 Daihatsu Sirion 1.3

1 Answer

Im am about to replace the Clutch Disk of my Sirion 2000. Do I need to take the engine out (downwards)?

Not familar with your car but you should be able to remove transmision downwards and replace cltch

Feb 17, 2011 | Daihatsu Charade Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides