Question about 2002 Audi A6

1 Answer

Hazard lamp switch 2002 audi a6 - 2002 Audi A6

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 43 Answers

Hazard lamp switches fail in these all the time.  When they fail they can cause the turn signals to go heywire like blinking and staying on or blinking and turning off or also not work at all.  In order to remove you need to carefully pry off panel around the switch.  I perfer using a very small straight screw driver and go around the four corners of the bezel.  Note normally some of these tabs will brake.  its ok as long as you have a few left to reinstall.  Once the cover is removed you will see the switch is infact a triangle cut out in a box.  To remove use to small straight screwdrivers and pry on both sides and it should pop out. Then just pull connector off back of switch.  Make sure connector doesn't fall back into dash this can be an issue trying to retrieve.   Always check new switch operation before reassembling.  

Posted on May 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Audi a6 avant door


If all else fails you may need to change the central lock system control module. You need to supply dealer with Vin #

Apr 01, 2014 | 2003 Audi A6

1 Answer

Have 2000 A6 2.8 awd, just replaced hazard relay but turn signals still do not work. What else could it be?


If you have replaced the hazard switch and you are still having issues, the next step to take is to replace the actual turnsignal switch on the column.

Dec 18, 2010 | 2002 Audi A6

1 Answer

My hazard warning switch light has remained on with everything switched off. The hazards work ok when the switch is depressed. The car is an Audi A6 2.7 TDI Quatro 2006.


Either 1 of 2 things. Relay inside hazard switch goes bad often. If that is not it, then usually you would end up replacing the actual turnsignal column switch. But a new Hazard switch should do it.

Dec 17, 2010 | 2006 Audi A6

1 Answer

Turn signals not working audi a6 2002


turn signal switch most likely. But it could have a faulty flasher relay. the signals and the hazards probably have seperate flasher relays and possibly on different circuits so check fuses as well

Nov 04, 2009 | 2002 Audi A6

1 Answer

My blinkers won't work, the light just stays on (not blinking) do I need to replace the flasher? Where is it? The hazards work. It's a 2003 Audi A6


The relay is built into the hazard switch. It could be that or the turn signal switch. Try the hazard switch first (it's relatively cheap). If that doesn't do it, you'll have to replace the turn signal switch, which involves removal of the steering wheel and airbag.

Oct 31, 2009 | 1999 Audi A6

1 Answer

I need to change the flasher relay on my 2000 A6 Quatro. I have removed the cover above the radio, to expose the hazard switch, but I cannot get the hazard switch out. How can I get the hazard switch out ?


The hazard switch is hard to get out. It has one clip on each side. By using a flat screwdriver on one side, and conciderable force, the whole thing came sliding out.

Jul 06, 2009 | 2002 Audi A6

1 Answer

2004 audi A6 flasher lights


You need a new hazard light switch - the relay for the hazards and turn signals is built in. It's $40 or so at a dealership to buy a new one.

May 19, 2009 | 2004 Audi A6

1 Answer

Indicator lights stay on perminently


its the signal switch on the colunm NOT the hazard switch

Apr 13, 2009 | 2004 Audi A6

1 Answer

Signal lights stay on


Its common for the sockets to burn up.  If you installed and the lights are still coming on.  The issue is the hazard light switch is bad.  If it were me I would replace the burnt socket anyway since it has been damaged and replace the hazard lite switch too.

Mar 19, 2009 | 2000 Audi A6

1 Answer

Audi a6 2.8 quattro


common problem with the hazard switch,if you press it in very gently or rapidly in and out your indicators will work,but you will need a new switch

Jan 04, 2009 | 2002 Audi A6

Not finding what you are looking for?
2002 Audi A6 Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...