Question about 1999 Chevrolet Astro
1996astro van no rear brakes and when you hit the brakes the pedal jumps and goes almost to the floor. Is it the master cilor te absstem.
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: no brake!
also check the brake booster usually when it goes bad the pedal goes to the floor causing no brakes.....try replacing that.....also a vacuum leak could cause that....are you loosing brake fluid at all besides when you bleed the brakes? let me know
Posted on Sep 30, 2008
The disc brake pads are NOT used for the parking brake. The parking brake uses mini-drum type shoes inside the rear disc rotor.
Take a look at http://wiki.answers.com/Q/How_do_you_change_the_emergency_brake_pads_on_a_2000_Chevy_1500_Silverado_Pickup
For more info
Posted on Jun 21, 2009
do you have a self bleeder kit? first off, you have to bleed the master cyl back into its self and the combination valve before you go to the wheels. when you do that, I think you will find that you have air in the lines. disconnect both brake lines from the master cyl and put the bleeder kit fittings on the master cyl, then put the rubber tubing with the kit on the fittings and submerge it in the brake reservoir. make sure its full. then pump the pedal until you get a hard pedal. if that is the case, reconnect the lines to the master, then have an assistant pump up the brake pedal with the engine off, and bleed the combination valve which should be connected to the master by steel tubing. pump it up, then hold it down, and crack the fittings loose, one at a time until the pedal goes about half way down, but do not release the brake pedal until the line is tight again, otherwise you will **** air in the lines. after you do all that, go to the farthest caliper or wheel cylynder from the master and bleed that with the same technique,and dont release the pedal until you close the bleeder screw. unless you have a major prob, this will work.
Posted on Jul 20, 2009
SOURCE: brake pedal dropping to floor
do u have the antilock brake bleeding tool? if not you will need to have the dealer bleed the brakes, the ABS control valve must be electricaly held open to bleed the brakes there of course is a special tool for this.
Posted on Oct 18, 2009
Testimonial: "Thank You"
Start with brake in the rear that is the farthest away from the master cylinder ( if your master cylinder is on drivers side start with passenger rear,pump up brake pedal until hard have someone else open bleeder valve until air or fluid squirts out,while holding brake pressure even if goes to the floor dont release pedal until bleeder valve is tightened or you will **** air back into the line,do this several times making sure you get a full stream of brake fluid and no air,continue to other rear wheel and then proceed to front wheel furthest from master cylinderand then final wheel. if you still don't have brakes change master cylinder and bleed all brakes again.
Posted on Jul 06, 2010
Tips for a great answer:
Oct 01, 2014 | 2002 Chevrolet Astro
Sep 30, 2014 | 2005 Chevrolet Astro
Sep 18, 2014 | 1996 Chevrolet Astro
Mar 19, 2011 | 1994 Chevrolet Astro
Dec 24, 2010 | 1996 Chevrolet Astro
Sep 04, 2010 | 1996 Chevrolet Astro
Feb 22, 2010 | Chevrolet Astro Cars & Trucks
Jan 09, 2010 | 1996 Chevrolet Astro
Nov 26, 2009 | 1997 Chevrolet Astro
Oct 10, 2009 | 2001 Chevrolet Astro
22 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: