Question about Cars & Trucks

Open Question

What is the function of sensor crankshaft pulley 4m40 turbo engine

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 38 Answers

SOURCE: How do I tell weither

Easy answer. When you look down from the top of the engine, there will be a small wiring loom that runs down the timing cover and enters very near the bottom. From memory it a two wire sensor. If this is the case u have a sensor type crankshaft pully.

Posted on Jan 04, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford Expedition 2001 crankshaft sensor location and installation


  • Located front of engine, close to crank pulley
  • press the helpful button and follow me on Fixya for more tips
  • Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.
  • Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioning compressor's pulley.
  • Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.
  • Pull the electrical connection off the crankshaft sensor.
  • Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.
  • Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.
  • Press the electrical connection onto the crankshaft sensor.
  • Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.
  • Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley. write up found @ehow

How to Replace the Crankshaft Sensor in Ford 150 eHow

Jan 28, 2016 | Ford Expedition Cars & Trucks

1 Answer

What do I have to take into account to exchange from a electronic fuel pump to a mechanical fuel pumplease on a 4m40 delica engine.


I don't see any way to do this, since the mechanical pumps are normally engine driven by a lobe on the crankshaft, unless this engine has that functionality built into it. Let me know if you figure out a way!

Mar 21, 2015 | Cars & Trucks

1 Answer

My car won't start


I am not sure about restart the engine,but I would check the crankshaft sensor or the crankshaft pulley...

When a crankshaft sensor has failed or is failing, certain timing problems will arise in engine function. The engine may start normally in some cases, but will cut off after a few minutes (or seconds) of operation. More than likely the engine will be unable to start at all. Since the crankshaft sensor is responsible for engine timing, the driver may experience engine backfire or irregular rpm function, if the vehicleicon1.png starts at all.

Dec 21, 2012 | Hyundai Motor 1999 Elantra

2 Answers

How do I tell weither the crank shaft pulley is a sensor type or non sensor typ. 1996 V26 Engine 4M40 2.8 turbo diesel


Easy answer. When you look down from the top of the engine, there will be a small wiring loom that runs down the timing cover and enters very near the bottom. From memory it a two wire sensor. If this is the case u have a sensor type crankshaft pully.

Jan 03, 2011 | Mitsubishi Montero Cars & Trucks

3 Answers

Pajero 4m40 2.8d turbo


in front of the deisel pump the gear wheel is slightly cut/chip mark to the back of it take it out, and place it on t or n (t for turbo n for non turbo) .normal timming is good .If not hand turn until #1 piston is up and #1 cam shaft lobes are not touching cup & shim then set pump to desired mark

Jun 03, 2010 | 1996 Mitsubishi Montero Sport

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

2 Answers

Were is the crankshaft position sensor located on 2001 chevy mali


It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Mar 22, 2010 | Chevrolet Malibu Cars & Trucks

6 Answers

1993 mitsubishi pajero exceed-intercooler turbo 2800 diesel engine 4m40


Hi, I have a Pajero 2800 Turbo 1995 Auto. It has developed a bad oil leak somewhere around the front right hand side (from the front) where there seems to be oil spraying over the pipes, etc. Can't see it happening with the engine running and have cleaned the engine off but still can't see where it comes from. It has emptied the sump! Any ideas?
Cheers,
Rob.

Jul 10, 2008 | 1995 Mitsubishi Montero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...