Question about 1996 Hyundai Accent

2 Answers

ECM location for 96 Hyndai Accent

Where is the location for ECM connector? SMOG report says it may have water damage and the OBD2 is not communicating with vehicles computer. Shop recommend repair ground and replace ECM.

Thanks for any help!

Posted by on

  • 4inpocket May 08, 2009

    Thanks for the response.



    I reviewed the document you referred me to and am still in need of more information. Seems this information is for jet ski's???



    My problem is a SMOG issue. The 1996 Hyndai Accent is running well and has no problems driving. Problem is, it will not pass SMOG because the vehicles computer has no communication to run SMOG test.



    Shop recommends to repair ground for ECM and replace ECM connector. They believe it may have water damage.



    Where is the ECM connector located?



    Thanks.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

It is located just above the fuse box behind the dash at the driver footwell.


Any further help, let me know.

Thanks for using Fixya.

Do rate the solution as "Fixya" if 100% satisfied.

Posted on May 08, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 413 Answers

Kindly go through this link ,will help you alot
http://www.sea-doo.net/Specifications/787-RFI-TROUBLESHOOTING-CHART.pdf

Posted on May 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

PONTIAC G6 2006 runs ok ck eng lite on OBD tool is getting power when connected but can not communicate where do I look for connection falts


No year make and model. I would guess the a computer has shorted and killed the data line. This would be a full car scan. If no computers could be scanned, then you'll need to find the bad one. Disconnect one at a time till you can read the others. If it is data lines or the computer. The full scan will read all the other ones. the others will pop a communication code to the suspected computer.

Dec 24, 2016 | Cars & Trucks

2 Answers

My 95 s10 has a obd2 plug And a obd1 you ecm how do I scan codes


try the obd1 connector to see it communicates. if not try the other one. some of the GMs didn`t use the obd2 connector in 94 until later on other models.

Aug 22, 2015 | Cars & Trucks

1 Answer

I need help to confirm location of sensor 2 bank 2. CEL detect P0161. There are 4 sensors in which two are above the catalyc converter and two are below the converter. The part department staff says the...


that Toyota has a 2.4 l 2az-fe 14of 155 hp and ran from 2001-2007 after which a v6 engine was installed
the sensor is the one before the cat converter as it is a heated oxygen sensor (KO2S) and reports on the gas composition to the ECM for air/fuel ratio adjustments
the oxygen sensor (O2) is after the cat converter and reports on the cat operation
have the cat converter checked at an accredited muffler shop

Jun 21, 2017 | Toyota Highlander Cars & Trucks

1 Answer

I failed smog because of obd2 connector has no communication how do i trace the no power on obd2 connector?


i dont now much about obd2 tool, but you can ask the 24 hrs live technical support http://www.diyobd2.fr/service/, they will like to help you, good luck

Sep 14, 2013 | 2001 Buick LeSabre

2 Answers

I took it to get it smog did not pass smog they said that computer did not communicate whit the car computer they said to check wire # 16


more specifics what is " it " what year, what make, what model, what engine, what state or region is the smog test being done? all that can be seen in the video is a cluster of wires. IF this vehicle is obd 2 check your cigarette lighter fuse or make sure you have 12 volts to the connector pin

Oct 16, 2012 | Cars & Trucks

2 Answers

Ecm will not communicate on the OBD11 connection to scan for codes


Hi Juanatijerin, Make sure that your vehicle has the sixteen pin connector and that it is OBD2 compliant. It could be fitted with the sixteen pin connector but compliant to OBD1. Check the ECU fuse. If that is okay check the power feed to the unit and the earth connections. Regards John

Oct 15, 2012 | 2000 Daewoo Lanos

1 Answer

P0340


I think the 2004 Accent only came with a 1.6 liter engine as far as I know. In any case below is as much information I have as far as your code including a wiring diagram of that circuit (CMP sensor). The wiring diagram doesn't tell the wire colors but does tell you where the wire goes or what "pin" number it is at the connectors. I included the connectors which is by number and marked the ECM connector for you. I had a picture of the CMP sensor location but not the ECM location but can tell you the ECM connector is located behind the dash fuse panel. Hope this helps....

3_15_2012_9_38_42_am.jpg3_15_2012_9_39_12_am.jpg

3_15_2012_9_39_37_am.jpg
3_15_2012_9_40_01_am.jpg

3_15_2012_9_40_24_am.jpg3_15_2012_9_40_49_am.jpg

3_15_2012_9_41_15_am.jpg

Mar 14, 2012 | Hyundai Motor 2004 Accent

2 Answers

P0727 trouble code how to fix


Description: Calculate damper clutch slip. Detect engine speed to control fluid pressure during shift.
Probable Cause: Malfunction of ECM, Malfunction of connector or Malfunction of TCM.
CHECK: Harness & Connector and CHECK: ECM.

Hope this was some help?

Jul 28, 2011 | 2000 Hyundai Accent

1 Answer

My check engine light is on- the reported error is p501 right wheel sensor failed smog- what part or parts do I need to correct this problem-where is the part located and guesstamate what the part might...


CODE PO501 VECHICLE SPEED SENSOR PERFORMANCE.POSSIBLE CAUSE IS FAULTY VECHICLE SPEED SENSOR.CHECK SENSOR WIRES AND CONNECTOR FOR DISCONNECTION OR DAMAGE.

May 12, 2011 | 2002 Kia Rio

Not finding what you are looking for?
1996 Hyundai Accent Logo

573 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...