Question about 1998 Holden VT Commodore

Open Question

Clunking noise when turning - 1998 Holden VT Commodore

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loud grinding/clunking noise when driving, lessens when I press the brake


Loud Noise Unknown Origin - Ask the GM Technician - GM-Trucks.com

www.gm-trucks.com > ... > Ask the GM Technician

Jun 30, 2006 - 7 posts - ‎3 authors
I get a loud clunking, grinding noise while turning to the right only, and ... I moved the passenger side tire to the rear driver side just in case it ...

can bad wheel bearing/hub cause loud clunking noises?

www.jeepsunlimited.com/.../showthread.php?...loud-clunking-noises

Nov 12, 2009 - 14 posts - ‎6 authors
driving home, i noticed some metal clunking sounds coming from the front driversside. at ... hmmmm....if it's grinding, then probably a bearing.

Front Clunking sound when driving straight. - TDIClub Forums

forums.tdiclub.com > ... > VW MKIII-A3/B4 TDIs
Dec 21, 2011 - I have a sporadic clunking noise from the drivers side front end. '98 jetta ... If I try to coast it gets really louder and more pronounced. ... whirring orgrinding could be several things: wheel bearing, brake pads due to a caliper ...

Quick Guide to Diagnosing Differential & Driveline Noises ...


Dec 26, 2015 | Cars & Trucks

1 Answer

Have a 2004 polaris ATP 500 when turning there's a clunking noise I changed wheel bearings and noise still there ! Checked u joints not really a lot of play in them!


2011 Sportsman 500 Trans Clunk - ATVConnection.com ATV Enthusiast ...

atvconnection.com/.../polaris/343211-2011-sportsman-500-trans-clunk.h...
Mar 21, 2012 - It is really noticeable when wheel is turned when you get on the gas from a. ... 2011 Sportsman 500 Trans Clunk ... You have to figure from the motor to the clutches,then to the transmission,then to the drive shafts,there is going ... 1999 Sportsman 500,slight clunk from dead stop
Feb 28, 2015
Clunk or pop in the steering on an 07 Sportsman 500 ...
Aug 8, 2008
500 HO, rear end noise
Apr 29, 2006
clunking noise on scrambler 500...
Jan 31, 2000
More results from atvconnection.com

Sep 25, 2015 | Cars & Trucks

1 Answer

Turns over then cuts off


Clunking noise sounds like a piston to crankshaft problem. You can do a compression test to determine the bad cylinder.

Jan 23, 2014 | Ford Expedition Cars & Trucks

1 Answer

Clunking noise while driving, turning steering wheel left and right, putting gas on pedal almost anything I do it clunks and check engine light is on.


while turning my wheel left to right , I here a clunking noise. what should I do or is it rubber some where worn out

Apr 13, 2013 | 2005 Chrysler Pacifica

1 Answer

Clunking noise when turning boxer van


One of the driving shafts cv bearing worn out ,Drive in the park turn left not noise turn right you have noise ,notes right turn noise is left cv and left turn is right vc join .2nd the most of the times the long-standing shaft damage the cv bearing first..

Sep 11, 2012 | Peugeot Peugeot Cars & Trucks

1 Answer

Clunk noise when turning right


Could be the drive axle, but may also be a shifting lower control arm or strut. Usually a faulty drive axle clunks every time the axle turns.

Jul 04, 2012 | 2002 Buick Century

1 Answer

I have a 1997 toyota rav 4 that makes a clunking noise whenever I turn the wheel. What is it?


Hi

Is it a clunk clunk clunk noise? Then you have a CV joint that needs to be replaced. This is called the CONSTANT VELOCITY JOINT, and helps you turn the wheel when it is in motion.

It has ball bearings inside and when the housing wears out, they make that clunking noise.

See your mechanic for a change and see if you can replace both wheels at the same time.

githinji.jpg

Hope that helps.

Happy motoring.

G

Feb 11, 2011 | 1997 Toyota RAV4

1 Answer

Grind sound while turning


Hi

Is it a clunk clunk clunk noise? Then you have a CV joint that needs to be replaced. This is called the CONSTANT VELOCITY JOINT, and helps you turn the wheel when it is in motion.

It has ball bearings inside and when the housing wears out, they make that clunking noise.

See your mechanic for a change and see if you can replace both wheels at the same time.

githinji_0.jpg

Jan 31, 2011 | 2006 Subaru Forester

Not finding what you are looking for?
1998 Holden VT Commodore Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...