Question about 2001 Dodge Stratus

1 Answer

Where is the blend door actuator located on a 2001 stratus rt

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 44 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: Blend door not working.

The bleed door controls air temp not where it comes out, dash, floor, defroster, this is most likely a mode control switch problem, that switch is on the ac control head.

Posted on Sep 23, 2008

arclight1217
  • 208 Answers

SOURCE: 2001 Dodge Stratus Transmission Problem

COULD BE LOSS OF ALL TRASMISSION FLUID, BROKEN HOSE, BLOWN PUMP,BURNT TRANSMISSION RINGS( HOW DID THE TRANNY OIL SMELL?) BURNT TRANNY FLUID OR A COMBINATION OF ANY OF THE ABOVE. IF IT JUST QUIT, YOU PROBABLY HAVE A SERIOUS PROBLEM THAT WILL REQUIRE A REBUILD OR A SALVAGE TRANSMISSION FROM A LOCAL WRECKING YARD. THE LATTER BEING THE CHEAPEST AND AT TIMES THE BETTER DEAL ALL AROUND, TIME WISE AND MONEY. VERSUS A REBUILD THAT REQUIRES NEW PARTS, BANDS, PUMP, SEALS AND ON AND ON PLUS HOURS OF LABOR TO FIX EQUALS ONE BIG BIG BILL!BEING A 2001 A TRANNY FROM A WRECKING YARD ISN'T GOING TO HAVE THAT MANY MILES ON IT EITHER SO YOU SHOULD BE ABLE TO FIND SOME PRETTY DECENT ONES. THAT'S THE ROUTE I'D GO, BUT YOU'RE FREE TO CHOOSE EITHER CHOICE. I DON'T ENDORSE OR CONDEMN EITHER ONE, JUST POINT OUT THE GOOG AND THE WEAK IN EACH FOR YOU TO DECIDE! GOOD LUCK! IF I CAN HELP REPLY TO: ARCLIGHT1217

Posted on Nov 12, 2008

  • 1 Answer

SOURCE: dodge stratus rt fuel filter location

were is fuel filter st on a dodge stratus 2001 4dr 2.4L DOHC

Posted on Jan 16, 2009

  • 51 Answers

SOURCE: how to change transmission fluid in a 2001 dooge

you need to take off the pan (leave the back ones in and remove all the others, then loosen the back ones to let the fluid out in the front. then remove the rest.)

Posted on Sep 08, 2009

  • 101 Answers

SOURCE: how to change transmission fluid in a 2001 dooge

loosen bolts on bottom of trans pan, pull one corner lower than others, drain fluid into large flat container. Remove gasket and filter. replace both. replace pan cover careful to keep gasket in position. check owner manual for amount of fluid to fill and type of trans fluid. DO NOT OVERFILL- EVEN 2 OUNCES OVER CAN RUIN SEALS

Posted on Sep 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of blend door actuator, Item 604-106


usually behind the dashboard about in the middle .dash has to be removed to fix .

Aug 20, 2015 | 2001 Chevrolet Tahoe

2 Answers

1998 Dodge Stratus - Air conditioning is blowing through the defrost vents


Vacuum controls this circuit and leaks will cause blend air door to default to defrost. Check for bad check valve or hose leaks under hood first as these are the easy ones to get at and under hood heat causes deterioration.

Jul 08, 2015 | 1998 Dodge Stratus

1 Answer

I'm trying to locate the blend door actuator on my


Google 2001 blend door replacement or actuator replacement
its not an easy job, I had to cut the duct work out to get at it
the videos are good

Oct 19, 2014 | Ford F-150 Cars & Trucks

2 Answers

Location of blend door actuator on 2001 Buick Regal


driver side actuator for blend door is electric servo controlled. It could be jammed or computer sending it in wrong direction. Unit is located on driver side of heater case.

Jun 03, 2014 | 2001 Buick Regal

1 Answer

Where is the blend door actuator located on 2006 Chevy Silverado?


My ac works, but my heater blows cold air. Is there any way I can replace actuator by going thru the glove compartment?

Nov 04, 2012 | 2001 Chevrolet Silverado

2 Answers

Heater wont work, fan runs, but cant chamge temp 2001 F150 SUPERCREW 5.4


Do you hear any clicking or popping noises coming from dash area when you try to change the temperature? If so, you have either a bad blend door actuator or a broken blend door. If it's just the actuator, you can find it by following the popping noise to the location. It is under the dash close to the passenger's side of the vehicle. The actuator is easy to change once you find it. If the blend door is broken, you will have to pull the dash out and remove the air plenum from inside the dash to gain access to the blend door.

Aug 14, 2011 | 2001 Ford F150 Styleside SuperCrew

4 Answers

NO heat in front of 2001 windstar van. Thumping


Blend air door may be stuck. I removed a pencil from a heater box before. It had fallen from the dash, down through the defrost vents and jamed the door.

Nov 13, 2009 | 2001 Ford Windstar

1 Answer

No heat Heater core is hot


If heater core is getting coolant circulating through it then you may have a temp blend door, or blend door actuator not working properly. The blend door is located in the air box under the dash, and the actuator is located on the air box. You may be able to visually check the operation while turning the temp knob, by locating the coresponding actuator on the air box and monitoring the movement. If it is moving ok and still no heat then the blend door, or lever is broken, which will require removal of the dash.

Oct 17, 2009 | 2001 Dodge Ram 2500 Truck

3 Answers

01 silverado blend door changed /now works back wards!!!


most likely needs a LH (bottom) temp actuator. Located in the center of the dash on the bottom, you have to remove the hush panel on the rh side of the truck

Apr 24, 2009 | 2001 Chevrolet Silverado

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
2001 Dodge Stratus Logo

693 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...