Question about Cars & Trucks

1 Answer

What tools do I need to replace the front hub assembly on a 2000 dodge grand caravan

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,384 Answers

Here's a link.

Posted on Nov 27, 2013

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 101 Answers

SOURCE: replacing front wheel hub assembly 1996 Dodge caravan

first jack up the van remove the wheel remove the brake caliper and rotor remove the axel nut then remove the three bolts on the back of the hub tap on the hub with a hammer it should come out hope this is helpful

Posted on Mar 19, 2009

  • 95 Answers

SOURCE: Replace the front wiper motor 2000 Grand Caravan Dodge

It is on the firewall under the hood. It has 3 to 4 bolts holding on. Be careful when taking it out to see how the new one lines back up. Hope it helps.

Posted on Mar 30, 2009

wyatt1582
  • 453 Answers

SOURCE: what tools do i need to replace front wheel bearing hub assembly

Floor jack- jack car up and put a jack stand under it. A tire lug to remove tire. A 36 mm socket to unbolt axle shaft sticking through bearing hub. Next a Brass hammer with a block of wood. Next center wood on axle shaft sticking through bearing hub and hit with a 4lb brass or steel hammer with a wood block on shaft. Next you need a 10mm or 12mm socket on back side of bearing hub should have 3 bolts holding it unbolt. Last use a pry bar and gradually pry bearing out and no there not pressed in like a lot of people think.
(Socket sizes maybe different)
If you take it somewhere it would cost about $800 and up.

Posted on May 03, 2009

airjer995
  • 5332 Answers

SOURCE: removing hub assembly on 2001 dodge grand caravan 3.3L 2wd

Remove the axle nut. Place a punch in the fins of the rotor to lock the hub in place when the punch hits the caliper. Remove the caliper and rotor. Unplug the abs sensor Remove the three bolts holding the hub assembly to the knuckle. Remove the hub assembly from the knuckle. It is vitally important to torque the axle nut to the proper spec. Failure to do this will cause the barring to fail quickly! Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Posted on Feb 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 grand caravan front wheel drive that needs a new rear bearing hub assembly. I have removed all except the assembly and it will not budge. Is there anything I can use to remove the hub other...


CHRYSLER WARNED AGAINST NOT USING A SLIDE HAMMER PULLER UNLESS YOU ARE GOING TO REPLACE REAR HUB AND BEARING ASSEMBLY.WHEN REPLACING HUB AND BEARING ASSEMBLY THEY HAS TO BE PRESSED OUT.

Sep 21, 2010 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

1996 caravan broke all bolts free hub assembly still will not


Rear hubs? according to book, need a special tool to pull them... according to a loal shop, bang on it til it releases... you will need to replace it anyways.... might look for a rental place that rents the tool.

Peace

Feb 27, 2010 | 1996 Dodge Caravan

1 Answer

Wheel Bearings


Hello tclinch.
Your Grand Caravan has hub assemblies front and rear. Also if yours is all wheel drive it has a rear hub as well. Just different removal processes.
Hope your repair goes well for you.

Nov 27, 2009 | 1999 Dodge Grand Caravan

1 Answer

I need to know what type of tool is required to remove the caliper on the front of a 2001 Dodge Grand Caravan.


I discovered that you need to remove the entire assembly in order to remove the rotor.So all I needed was the socket to remove the hanger that the caliper was attached to.

Nov 01, 2009 | 2001 Dodge Grand Caravan

1 Answer

WHERE ARE THE VEHICLE SPEED SENSORS LOCATED ON A 2002 DODGE GRAND CARAVAN 3.3L 2WD


Both front wheel hub assembly would have those sensor they are also used for the abs. I am not sure on that year of caravans would have some on the rear wheel hub assembly also.

Oct 09, 2009 | 2002 Dodge Grand Caravan

1 Answer

Reset a/c switch in dodge grand caravan


I need more info to solve this. You're giving so little info,sry.

Jun 22, 2009 | 2000 Dodge Caravan

1 Answer

What tools do i need to replace front wheel bearing hub assembly


Floor jack- jack car up and put a jack stand under it. A tire lug to remove tire. A 36 mm socket to unbolt axle shaft sticking through bearing hub. Next a Brass hammer with a block of wood. Next center wood on axle shaft sticking through bearing hub and hit with a 4lb brass or steel hammer with a wood block on shaft. Next you need a 10mm or 12mm socket on back side of bearing hub should have 3 bolts holding it unbolt. Last use a pry bar and gradually pry bearing out and no there not pressed in like a lot of people think.
(Socket sizes maybe different)
If you take it somewhere it would cost about $800 and up.

May 03, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Replace the front wiper motor 2000 Grand Caravan Dodge


It is on the firewall under the hood. It has 3 to 4 bolts holding on. Be careful when taking it out to see how the new one lines back up. Hope it helps.

Mar 30, 2009 | 2000 Dodge Grand Caravan

2 Answers

Replacing front wheel hub assembly 1996 Dodge caravan


You can get a complete hub with bearing and its can just be bolted on, without having to have bearing pressed in and out. Good luck and thanks for using FIX YA

Mar 19, 2009 | 1996 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...