Question about Audi A4

1 Answer

Pixelated read out - A4 Audi Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Hi Rick
You will need to have your instrument panel removed and sent to a specialist to have the pixel display repaired,If you remove the instrument panel yourself,First disconnect the battery,Make sure the keys are not in the car when you do this,Depending on the age of your Audi you may be able to get this done free of charge by an Audi agent,As this is a common fault on Audi.

Posted on Nov 27, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 buick century 3.3 what should the fuel injector ohms be reading or the voltage should be reading. i checked mine 4 of them are reading in the 20s voltage


Ohms should read 11 to 15 at the injector pins. Power at the plug should be battery voltage. 12.5 with key on. Use a noid light to see if the injector wires/PCM is firing the injectors. the light should flash when cranking the engine over.

Oct 15, 2016 | 1992 Buick Century

1 Answer

2002 Town and Country. Why does it have a rough idle, dies when stopping, has sluggish power, and sounds terrible?


Suspect throttle positioning sensor (TPS)...can be tested...need a meter set to read 5 volts DC...Tps is located on throttle body...it has a three wire connector with wire colors: Brown/Orange...Dark Blue/Dark Green...And Pink/Yellow...Engine off...Push points of safety pins deep into into rear of in place connector PLUS METER LEAD on Brown/Orange wire and NEGATIVE METER LEAD into DarkBlue/DarkGreen...Set meter to read 5 volts...Start engine...At idle (Yes, I know it is running rough) then read meter...RECORD READING...Next rev engine to full throttle...RECORD READING...First reading must be .08 volts...Second must be 4.5 volts...If second reading is less than 3 volts...example 2.4volts TPS is culprit...Replace TPS...all readings OK? Let me know...saailer

Jun 23, 2015 | Chrysler Cars & Trucks

1 Answer

I have a mastercraft multimeter, it reads volts but wont read milliamps. Checked the fuse, it's good. what else could be the problem? There is only one fuse on the inside, does it protect both volt...


Tom,
Do you get any readings from the meter when attempting to read amps? Are you connecting the meter properly? Some people assume that you touch the test points the same as a voltage reading but that of course is not correct to read amps. You must use the meter to bridge the connection so that the current flows through the meter, otherwise you will get a zero reading.

Jan 03, 2015 | Cars & Trucks

1 Answer

Very hard to read dashboard on a6


My brother in law who lives in nottingham or winchester has one of these audis-we all hate them at my shop-I tell him to get a nice lotus seven- they are fun-and fun to drive- cheers Denny

Nov 27, 2013 | Audi A4 Cars & Trucks

1 Answer

Oxygen reads 11.5 what is safe oxygen reading


You are reading the heater circuit of the oxygen sensor,a vehicle that is in fuel control will cycle a reading form 0. 2 volts to 0. 8 volts. this a good reading as engine are naturally aspired engines.

Feb 29, 2012 | Cars & Trucks

1 Answer

In dash reading reads " Gearbox Fault". I don't


It means you have a problem in the shifter. Is it a five or six speed?

Jan 11, 2011 | 2003 Jaguar X-Type

1 Answer

Code pooo1 fuel volume regulator control curcuit open map sensor reading 99 this is on xtype diesel this reading is with just ingnition on when runnig reading goes up but never below 99 is map sensor...


Hello! The PERCUS...E...Code is an Electronic Control Module (ECM) programming error or failure...The grounding may be at fault...Using an ohm meter set on X10 scale...Read from center of negative battery post to bare metal on chassis and then to engine block...Should read very near zero ohms...If these readings are OK...The ECM needs to be re-flashed (reload software) at a dealership.

MAP reading across wire colors Black/White (+) and Black/Green (-) at idle should be 1.1 volts...(.99 is a correct reading)...Throttle up and voltage increases to 3.75 volts w/o erratic movement...This indicates MAP is OK...

Guru.............Saailer

Sep 19, 2010 | 2003 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...