Question about 2002 Chevrolet Malibu

Open Question

Need to locate the ecm on 2002 chevy malibu 3.1L

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ajkill
  • 2035 Answers

SOURCE: need schematic for location of ECM on 2002 Chev Silverado 5.3L GAS ENGINE

Please use this link :

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801b6773


Good luck...

Posted on Aug 14, 2008

hondakilla
  • 129 Answers

SOURCE: ECM Location

For one i dont need your vin its a z24 which means it has a 2.4l engine it does not have an ECM it has a PCM powertrain control module, which is located for your car in the right rear corner topside of your engine bay, in 1995-2001 it is located inside the right front fender. I hope this info helps...

Posted on May 02, 2009

  • 77 Answers

SOURCE: thermostat on a 2002 chevy malibu

Which engine>? There are a few different engines available.

Posted on Jul 28, 2009

c17hydro
  • 2984 Answers

SOURCE: Where does the flasher go on a 98 chevy malibu

Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.

  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Posted on Dec 01, 2009

Testimonial: "just what I needed, thank you so much."

  • 5 Answers

SOURCE: need location of fuel filter on 2001 chevy malibu, 3.1 v6

underneath car driver side

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is PCM of 2002 Chevy Malibu?


The PCM is located just next to the 16 pin OBD2 diagnostic connector under the driver's side dash. The PCM is perpendicular to the firewall with the electrical connector facing downward.

Jan 01, 2016 | 2002 Chevrolet Malibu

1 Answer

Where is the fuel pump located on a chevy malibu 2002


The fuel pump is located in the fuel tank. You will need to lower the fuel tank in order to service it.

Jan 23, 2011 | 2002 Chevrolet Malibu

1 Answer

Where is the faulty switch on a chevy malbu


For what fault? There is no master fault switch. The ECM diagnoses and keeps tracks of faults and sensor readings. If you want to know what switch may be faulty we would need more information on the fault itself.

Dec 01, 2010 | 2002 Chevrolet Malibu

2 Answers

Chevy 2002 Malibu ERG valve


Symptoms of a bad EGR valve are usually stumbling idle or the engine stalling when the car is warm (normal operating temperature). Find the EGR valve and locate the vacuum line attached to it. Start the engine cold and wait for it to warm up. When the engine starts to stumble, pull off the vacuum line. If the EGR is bad, the engine idle will stabilize and no longer stumble.

May 25, 2010 | 2002 Chevrolet Malibu

1 Answer

Thermostat on a 2002 chevy malibu


Which engine>? There are a few different engines available.

Jul 28, 2009 | 2002 Chevrolet Malibu

1 Answer

ECM Location


For one i dont need your vin its a z24 which means it has a 2.4l engine it does not have an ECM it has a PCM powertrain control module, which is located for your car in the right rear corner topside of your engine bay, in 1995-2001 it is located inside the right front fender. I hope this info helps...

Apr 07, 2009 | 2002 Chevrolet Cavalier Coupe

2 Answers

Cannot locate horn for a 2002 Chevy Malibu


the horn is behind the passenger front fender. right in front of the tire. you need to remove the dust cover to gain access to the horn(s).
the picture was shot from underneath the car. you can not get to the horn(s) any other way.

cannot-locate-horn-2002-chevy-malibu-i42l1bq1qrxu2fudnsefqnkk-4-0.jpg

Mar 20, 2009 | 2002 Chevrolet Malibu

1 Answer

Where is the flash located in a 2002 chevy malibu


It is on the Fuse panel under the Dash on the Drivers Side at the Top Right Corner of the Panel.

Jan 18, 2009 | 2002 Chevrolet Malibu

1 Answer

2002 malibu ECM


not bad ecm it has to be programed by a dealership to mach your cars electronics radio,lights,sensors,ect,ect,ect

Sep 29, 2008 | 2002 Chevrolet Malibu

Not finding what you are looking for?
2002 Chevrolet Malibu Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...