Question about Jeep Cars & Trucks

1 Answer

2002 Jeep Wrangler - When the clutch is fully pushed in, it engages the starter. You can start the vehicle by just pressing on the clutch.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,198 Answers

That's unusual. Anyone not familiar with that system would not be able to start the vehicle, would end up breaking the key trying.

Posted on Nov 27, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2007 jeep wrangler sahara with a mopar remote starter just beeps

That's not a remote starter on your key chain, it's a keyless entry for an alarm system.

Posted on Dec 17, 2008

  • 6982 Answers

SOURCE: push down on clutch pedal can't get car into gear

Likely, you have a hydraulic clutch system. Check clutch master cylijnder for fluid and leakage, check hydraulic line and slave cylinder for leaks. If fluid low or empty, bleed as you would a brake wheel cylinder. If full,have someone work the clutch while you watch slave cylinder to make sure it is moving clutch fork. If system full and little or no movement, the master may be "bypassing" internally (replace) Also, check pedal mechanical linkage. Not often but sometimes these parts can break! Could also be athat clutch itself is worn, but this does not happen overnight and you would have noted slip long before this!

Posted on Dec 29, 2008

  • 1118 Answers

SOURCE: 1991 jeep wrangler sahara shifting promblems

Your clutch is not disengaging. If it a hydrolic clutch chk. the fluid in resavor, Or slave cyl. for the clutch is bad, Or it has got air in it and needs to be bleed. This is a clutch problem, nothing wrong with trans. If its a manual clutch linkage its an ajustment thing. My best guess if its hydrolic slave cyl. went bad, or resavor is out of fluid.

Posted on Feb 10, 2009

  • 1 Answer

SOURCE: when clutch pushed in it makes high pitched squeel

Im a mechanic, i think you will find it will be the clutch release bearing on the clutch fork, when you push the clutch in it will push the fork which will push the clutch release bearing onto the clutch plate which rotating with the engine revs

Posted on Mar 23, 2009

  • 316 Answers

SOURCE: Starter problem 1988 Jeep Wrangler

I sit here on this site and help people with their issues all the time, and I do it for free. I've been in the mechanics trade for over 24 years, and I think I have a good idea of what I'm talking about. I don't know it all, and I even need assistance from time to time. The only thing I ask in return for my help, is a good rating from the people I help. Once you replace your solenoid, your issue will be resolved. Yes the fix is that simple. Remember to disconnect the negative cable from the battery before you replace it, so you don't ground anything out.

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sport


Hi Maury, Seems you have a number of different problems at the same time. The grinding sound when pushing the clutch pedal would seem to be the clutch thrust release bearing, which is located inside the bell housing and requires the removal of the gearbox to replace. The warning lights should come on each time the ignition is switched on and then they should extinguish after a few seconds. The illumination of these lights is a fail safe system to show that all warning systems are active. The radio will go off during the period when the starter is engaged as a relay shunts all power to the starter during that procedure. The starter motor uses more power from the battery than any other system. The manufactures have taken this into consideration when designing the circuitry and decided as many others have, to adopt the operation. If when starting from cold this does not happen and the radio plays, it is indicating either excessive drawing of power by the starter and may also be the cause of the grinding noise you experience? Regards John

Jul 21, 2013 | 2000 Jeep Wrangler

1 Answer

2002 vw jetta vr6 no start no crank, but able to pop start


Start by checking the switch above the clutch pedal ... I have seen where they come loose, brake or move and when you push in the clutch it doesn't engage the safety switch all the way.

Nov 05, 2017 | 2002 Volkswagen Jetta TDI

1 Answer

1994 wrangler will not shift into gear when stopped but works just fine when moving.


No. The jeep moves when starting the engine as if the clutch isn't fully engaged, but only then. Sitting idle with the clutch depressed it is fine.

Sep 22, 2010 | 1995 Jeep Wrangler

1 Answer

Clutch pedal, starter, ignition... where is the safety relay for the clutch pedal depression to allow start? 1994 Jeep YJ 4.0 this has happened twice


If you find the switch, you can temporarily jump across it, 'till you get a new one. When you go to buy it you are looking for a clutch switch.
Neutral switches are found on automatic trans vehicles. If you jump it out, be VERY careful to make sure you start in neutral with the clutch depressed as without the switch, it will start in any gear even with the clutch engaged.

Oct 29, 2009 | 1995 Jeep Wrangler

2 Answers

Vehicle won't start, it has clutch interlock, which is only activated in 2wd and 4H , vehicle starts in 4L only, clutch switch??


Take it to the Jeep dealer . It's still under warranty. Won't cost you a penny. Good luck.

May 23, 2009 | 2009 Jeep Wrangler

1 Answer

Everything is good just wont start


sounds like the clutch safety switch is bad. it detects taht the clutch pedal is depressed to the floor and alows the starter to engage

May 15, 2009 | 1997 Jeep Wrangler

1 Answer

1995 jeep wrangler starting problems


would replace starter and inspect battery, cables/terminals also if problem still chattering u may have damaged the fly wheel the chattering is the starter not fully engaging the fly wheel. most likely starter but bad battery cables would also cause same symptoms hope this helps u

Apr 02, 2009 | 1995 Jeep Wrangler

1 Answer

1991 jeep wrangler sahara shifting promblems


Your clutch is not disengaging. If it a hydrolic clutch chk. the fluid in resavor, Or slave cyl. for the clutch is bad, Or it has got air in it and needs to be bleed. This is a clutch problem, nothing wrong with trans. If its a manual clutch linkage its an ajustment thing. My best guess if its hydrolic slave cyl. went bad, or resavor is out of fluid.

Feb 10, 2009 | 1991 Jeep Wrangler

2 Answers

89 wrangler


there should be a sloenoid on the firewall it could be bad

Aug 26, 2008 | 1989 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...