Question about Ford F-150

1 Answer

Ingnition switch broken in pieces - F-150 Ford Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Can u trun to the run pos. if so 2 holes will line up can insert a pin and slid out switch and put a new 1 in

Posted on May 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Switch is broken I need to cross wire in ingnition to start but need diagram of wire and colors


What make , model , year and engine size ? That doesn't work on a lot of vehicles now a days ! Anti-theft systems , programming in the control modules . Plus on some the start circuit is a input to the PCM or the BCM , an hot wiring will not work .

May 17, 2017 | Cars & Trucks

1 Answer

Ingnition switch


Can you hold throttle pedal down a bit and stay running? EGR might be stuck open. Vacuum leak from broken hose will cause this.

Nov 14, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

Ingnition won't turn past the accessory position


There is a piece of forged metal that is called a rack that attaches to a rod that gies down to the bottom of the column to the Ignition switch these racks have been known to break and jamb up and I have also seen Ignition switches jamb also. Go to the base of the column and remove the switch and see if the key lock cylinder moves all the way now. Then trace your problem to either a jambed Ignition switch or a bad rack and rod.

Jul 26, 2010 | 1989 Chevrolet Camaro

1 Answer

Replace ingnition switch on a 1995 vw passat ?


You must also remove the wiper / turn signal switch cluster. Before you can do this... Most of the 1995 Passats were fitted with a splined cone fitted on the steering columb just under the steering wheel. However a special pullers is needed to remove this cone. With this cone and the trim around the switches removed its a simple enough to remove the ignition switch.
All the best
John

Aug 15, 2009 | 1995 Volkswagen Passat

1 Answer

I installed a new ignition switch in my 1988 mustang


there is a ingnition rod going from key switch to ingnition switch ,it is probly not in the slot any more or the ingnition cam is broken

Jun 28, 2009 | 1988 Ford Mustang

1 Answer

I need instructions on how to put a locksmart switch ingnition


this not something that a back-yard mechanic should tackle

Mar 15, 2009 | 2002 Ford SVT Focus

1 Answer

Ignition replacement


Do you have tilt steering? if so the mechanism that actuates the ignition switch down low on the upper side of the steering column is damaged, you will need to pull it apart and check for damaged broken parts.

Aug 13, 2008 | 1995 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...