Question about 1999 Ford F150 Regular Cab

1 Answer

What is the torque for a 2001 f-150 rear axle seal?

Posted by on

  • Greg Margossian
    Greg Margossian May 11, 2010

    Are you referring to the Dana Axle or the Ford 8.8 Inch And 9.75 Inch Ring Gear?

  • yadayada
    yadayada May 11, 2010

    seals don't have torque specs, so what is it u want?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Just sung then 1/4 turn

Posted on May 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change rear transmission seal, or whatever its called.it came out and all my fluid came out on ground


There are 3 seals on this. 2 axle seals, 1 torque converter seal. If it is an axle seal, pull the axle and replace it. If it is the converter seal, you have to remove the transmission. Seals don't come out. If it did, you have other problems inside the transmission.

Nov 20, 2015 | 2001 Nissan Maxima

1 Answer

Rear end is leaking fluid where it connects to the drive shaft


you mean rear axle pinion seal. to change it you need to remove driveshaft. take a torque wrench to see the running torque. then remove center nut ,remove yoke. with screwdriver remove seal; reverse proc. then tight center nut to torque you find before you remove the center nut.

Sep 21, 2013 | 2001 GMC Jimmy

1 Answer

How to remove rear wheel bearings on my 1999 Ford Expedition and how do i know what pulley to rent/buy?


The 1999 Ford Expedition is built on an F150 platform. The Expedition uses a 9.75-inch rear axle. The axles are retained with C-clips at the end of the axle shaft, inside the differential carrier. The axle bearings are of the roller type. A failed axle bearing can manifest itself as a noise at the rear wheel or gear oil leaking past the oil seal. When replacing axle bearings, the oil seals must also be replaced.
Torque the caliper mounting bolts to 30 foot-pounds. Torque the bolt to 20 foot-pounds with a torque wrench and socket. Click this link below for complete detailed procedure:--- http://technoanswers.blogspot.com/2011/06/how-to-remove-rear-wheel-bearings-on.html -------------- This should help.Thanks.Helpmech.

Jun 07, 2011 | Ford Expedition Cars & Trucks

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

1 Answer

I am replacing the seal on the rear penion i need touqe specs on the nut


PINION FLANGE & OIL SEAL

CAUTION: Following procedure must be used to retain proper pinion bearing preload. Failure to follow procedure may result in premature axle assembly or component failure. Ensure pinion bearing preload is checked before disassembly, as previous pinion bearing preload will be used during reassembly.

Removal

1. Raise and support vehicle. Scribe reference mark on drive shaft-to-pinion flange on differential for reassembly reference. Remove bolts and "U" joint straps at pinion flange on differential.
Disconnect drive shaft from differential.
2. Remove rear wheels and brake drums to prevent any drag that may affect pinion bearing preload reading. Using INCH-lb. torque wrench, measure amount of force required to rotate pinion. This is pinion bearing preload. Record pinion bearing preload for reassembly reference.
3. Using Holder (6719), hold pinion flange. Remove pinion nut and washer. Scribe reference mark on pinion flange-to-pinion for reassembly reference. Using appropriate puller, remove pinion flange from pinion. Remove oil seal from axle housing.

Installation

1. Ensure oil seal surface in axle housing is clean. Coat lip of oil seal with gear lube. Install oil seal using appropriate seal installer. Drive oil seal into axle housing until oil seal installer contacts axle housing.
2. Install pinion flange on pinion with reference mark aligned. Using appropriate pinion flange installer, install pinion flange on pinion.

CAUTION: Washer must be installed on pinion with convex side of washer facing outward (away from pinion).

3. Install washer on pinion with convex side of washer facing outward (away from pinion). Install NEW pinion nut. Tighten pinion nut to 210 ft. lbs. (285 N.m). Rotate pinion several times to seat pinion bearings.

CAUTION: DO NOT overtighten or loosen then retighten pinion nut when adjusting pinion bearing preload. If pinion nut is overtightened, collapsible spacer on pinion must be replaced.

4. Rotate pinion using INCH-lb. torque wrench. Rotating torque should be equal to reading recorded in removal step 2) , plus 5 INCH lbs. (.056 N.m). If rotating torque is low, tighten pinion nut in small increments until proper rotating torque is obtained.
5. To install remaining components, reverse removal procedure using NEW "U" joint straps and bolts. Ensure all reference marks are aligned. Tighten bolts to specification. Check lubricant level and add if necessary.




Jan 23, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

I want replace the rear axle bearings on my 1985 suburnban


locking differential jack up and support rear of truck drain and remove rear cover remove lock bolt than slide out pinion shaft have someone push in on axle and remove c-lock do 4 both axles w/c-locks out remove axles carefully pry off oil seals-will need bearing puller and installer most auto stores rent or let u borrow them- reinstall new bearings and oil seal carefully install axles not 2 damage new oil seals reinstall c-locks and pull back on axle to lock in place slide in pinion shaft reinstall locking bolt torque to 25 ft-lbs reinstall cover and fill with gear oil

Sep 26, 2009 | Chevrolet Suburban Cars & Trucks

1 Answer

2005 chevy 4x42500hd


Hi..
On your 05 Chevy 4X4 2500HD.
The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

I hope this help on your question.

Thank you for use fixya...

Nov 04, 2008 | 2008 Chevrolet Silverado 2500HD 2WD

1 Answer

Pinion seal leaking


check your rear diff vent if pluged clean it out and clean up the pinion seal.sometimes if the leak is caused by pluged vent and has not been leaking long once vent is clean sometimes the leak will stop.there is not a specific torque amount because it is rotational torque(how hard to turn pinion).there is a crush sleve on the pinion and if torqued too tight or too loose brg preload will be wrong and brg damage could result.mark and remove drive shaft.remove rear wheels,brakes,axles.so when turning pinion you dont have any drag from brakes or axles.mark the position of the yoke on the pinion.remove yoke,replace seal,reinstall yoke be sure to replace pinion nut.tighten nut until it takes the exact same amount of force to turn pinion as before taking original pinion nut off.hope this helps.

Oct 22, 2008 | 2004 Ford F250

Not finding what you are looking for?
1999 Ford F150 Regular Cab Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...