Question about Ford Lincoln Continental

Open Question

Diagram for 2001 lincoln town car cooling system

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

old marine
  • 1973 Answers

SOURCE: need routing diagram for 2000 lincoln town car serpentine belt

There's a diagram at this link.

Posted on May 11, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: heat wont work 2001 lincoln town car cartia

Hello Callahan5922....this sounds like a stuck blower motor resistor. I assume the blower won't function in the a/c mode either? If you have a digital multimeter you can check this. I believe it's fuse #2....if the digital indicator goes up or down when you increase or decrease the fan speed thats good. Locate the blower motor resistor....you wil find it located on the fire wall behind the right valve cover hiding behind the heater hose, it's about the size of a cigarette pack. With the engine off, and key in on position, turn the A/C on High, and rap a tap tap tap on the resistor. You might be suprised when the blower motor takes off a runnin,
I hope this is the answer you need and i was able to help solve this for you. Good luck...

Posted on May 13, 2009

ArcAiN6
  • 152 Answers

SOURCE: need a wiring diagram

Unfortunately, this type of information is not provided by the manufacturer's as a download. However, there still remain's a solution. You can go to most automotive supply stores, and purchase manuals for your vehicle that contain step by step proceedure's to repairing almost everything on your car, these manuals usually also detail the electrical wiring in diagrams in the back of the manuals.

You can find these manuals at most automotive stores such as Autozone, Petboys and such. They usually rin from $8 - $20+ depending on how detailed the manuals are.

Posted on May 30, 2009

  • 5 Answers

SOURCE: 1997 lincoln town car 4.6 with a p0430 fault code

I will make an assumption here, we know what the root word means. This code was extracted from the computer by? What this is telling you one of 2 things: The Bank 2 oxygen sensor down stream of the catalytic converter (there are 2 converters, one for each bank of cylinders on the 4.6ltr engine) is bad and/or that the Bank 2 catalytic converter is no longer doing the job it was designed to do. Simply, Catalysts wear out. They are good for approx 100,000 miles (as required by Federal Law). Again, I assume that the reason the intake manifold was replaced was because it had a crack in one, or more, of the runners? (part that feeds the head of a manifold). It may have taken a while to find this as being the cause of why the car running incorrectly, maybe rough. This means, that during the time the car was being driven with the problem, the amount of unburned, or not within spec exhaust gases, coming off the side of the engine affected by the intake issue was higher than normal. This out of balance level of exhaust gases were being dumped into the converter on that side of the engine, thus causing the converter to have to run hotter, work harder, or even at the time the gas was being processed through, causing deposits to be formed in the converter, thus shortening it's life span. The Bank 1 side of the engine, apparently, did not have the issue and it's catalytic converter's life was not affected. I hope this makes sense to you.

Posted on Aug 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Finding the cooling fan control module on my 2001 Lincoln town car


There is no cooling control module . The PCM - engine computer controls the fan through the use of relay's . Cooling fan low an cooling fan high relay's

Apr 05, 2017 | Lincoln Cars & Trucks

2 Answers

Fuse number for a 1992 lincoln


92-94 Lincoln Town Car Fuse Box Diagram - Auto Fuse Box ...

www.autofuseboxdiagram.com/8895-92-94-lincoln-town-car-fuse-box-...
Sep 11, 2012 - 92 94 Lincoln Town Car Fuse Box Map 276x300 92 94 Lincoln Town Car Fuse Box 92-94 Lincoln Town Car Fuse Box Map. Fuse Panel Layout ...

Aug 26, 2015 | 1992 Lincoln Town Car

1 Answer

Where can I get a fuse box diagram for a 2001 Lincoln town car that I can print off online?


If you Google 2001 Lincoln town car it comes right up on the screen. You can print it from there.

Sep 27, 2014 | 2001 Lincoln Town Car

1 Answer

Diagram for belt assembly fo a 2001 lincoln town car


You have probably found this by now but here goes.
s7029.jpg

Jan 12, 2011 | 1999 Lincoln Town Car

1 Answer

2000 Lincoln Town Car (Engine Service) found a EVAP System?


Check your gas cap. If someplace can test it you might luck out. This website advertises manuals and info online. The evaporator cannister is suppose to purify excess fuel vapors. But a system which is not sealed will code an error lamp.

May 05, 2009 | 1999 Lincoln Town Car

1 Answer

2001 lincoln town car winshjield wiper


where is the fuse box for my 2001 lincoln towncar looking for windshield wiper fuse because they wont turn on what so ever

Mar 07, 2009 | 1997 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...