Question about Cars & Trucks

Open Question

Grill tek clip-on multi-timer --- lost directions

--- I lost the directions

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove grill vw crafter 2015


25627252-cvq3qatcgrsuar2pir1fl3t4-1-0.png
Carry out following work: Removing: - Undo and remove bolts -4- at top from radiator grille -1-. - Lever out spreader rivets -3- (Qty: 4) from below using a screwdriver. - Push thickness gauge -6- with the thickest feeler (1 mm) into space between radiator grille trim -2- and clip -5-. Note
This releases the latch -arrow-. - Using the front end hook -3370--7-, pull the radiator grille trim -2- out of the clip -5-"carefully" in -direction of arrow-. Fit on the right-hand side. - With help of a second mechanic, pull radiator grille trim -2- parallel out of the clips -5-. Caution
Radiator grille trim -2- is seated very tightly in the clips -5-.

25627252-cvq3qatcgrsuar2pir1fl3t4-1-2.png
- Remove bolts -2- on left and right. - Remove radiator grille -1- upwards.
IF U NEED FURTHER INFO LET ME KNOW..

Apr 04, 2015 | Volkswagen Cars & Trucks

1 Answer

How do you replace the grill on a 2003 Mercury Sable, what is the part name/number for the clips?


Retaining clips for the grill. Dealer only. Are the plastic tabs still on the grill? If not, forget the clips. Silicone it in place. Use tape to hold it and let it set for a day.

Jun 20, 2012 | 2003 Mercury Sable

1 Answer

Remove front bumper 1999 tarago


Hi
This is how you remove the front bumpers from 1990-2000 model Toyota taragos/Previas
First if your tarago/previa has a bull bar it has to be removed, before you can remove the front bumper.

There are 6 X 18 mm bolts secured to the bull bar brackets, remove the 3 x 18mm on the left and 3 x 18mm on the left and place the bull bar in a secure area to reattach later, don't be surprised if its full of rust it needs to be sand blasted, rust treated and repainted.
The next step is to remove the bull bar brackets to do this you must remove the grille to access the 4 x 18mm bolts on the inside of the grille 2 x 18mm on the left and 2 x 18mm on the right.

Open the bonnet of your tarago/previa there is a screw at the top of the center of the grille that has to be removed and placed in a container to reassemble later.

The next step is a bit tricky but with persistence and practice you will get better, the grille has four plastic clips that hold the grill in place.


Now listen carefully, you cant just pull on the grille firmly and hope that strength alone will pop the grille, these clips are designed to open when the grille is pushed into place so the top and bottom of the clip have to be depressed to slide the insert out to remove the grille, but you can depress one side a time it dosent have to be both at the same time.


It just takes take and patience to do, start from the top left clip, pull the grille towards you and with a flat blade screw driver look down the grill and press the top of the clip still pulling the grille, the clip will depress but now you have to do the bottom of that clip too.


There are gaps in the grille you need a tool like a L shape pick or an interior tool shaped like a L for removing door trims, you can buy these items at $2 dollar shops, you feed the tool through the gap in the grille and place it under the bottom of the clip and when you press down it lifts up depressing the bottom of the clip while you are still pulling the grille towards you.


Once that clip is out stay on the left side and do the left bottom clip repeat the process and then do the right top clip and then the bottom right clip, when the grill is out push all the clips back into the grille so you don't loose them and place grille in a secure place until your ready to reassemble.


When you reassemble the grille you just place the grille over the insert holes and push them back into place they will automatically snap back into position and then screw the center top grill screw back in.


Now the grille is out, you will need an extension on your ratchet to reach and remove these bolts 4 X 18mm bolts, 2 on the left and 2 on the right, there is a dryer bottle on the left or right of your vehicle depending on country, so the extension needs to be reasonable long.


Once the brackets are removed place the bolts into your container, there are 4 x10mm bottom bumper bolts securing the bumper onto the reinforcement bar remove them.


Then there are 2 X 10mm upper corner bumper bolts securing the bumper to the body remove them, and then the last 2 X 10mm to be removed are at the bottom of the corner bumper secured on to a rail.


Once these 10mm bolts are removed the front bumper will slide off, place the bolts in your container and reassemble when ready.


Cheers



11_25_2012_11_59_18_pm.jpg

Jun 07, 2012 | Toyota Cars & Trucks

1 Answer

How to install a grill for a 2001 volkswagon beetle


TO REMOVE GRILLE FROM BEHIND THE BUMPER COVER RELEASE PLASTIC CLIPS AND DETACH THE GRILLE. IF YOU HAVE FOG LIGHTS DISCONNECT THE ELECTRICAL CONNECTORS FROM THE FOG LIGHTS AND REMOVE THE FOG LAMP MOUNTING SCREWS BEFORE DETACHING THE GRILLE.WHEN YOU INSTALL GRILLE PLACE GRILLE IN POSITION AND SEAT THE CLIPS INTO HOLES IN THE BUMPER COVER. IF YOU HAVE FOG LAMPS INSTALL GRILLE IN POSITION THE INSTALL FOG LAMPS MOUNTING SCREWS BACK IN PLACE TO HOLD GRILLE IN POSITION.

Sep 25, 2011 | Volkswagen New Beetle Cars & Trucks

1 Answer

2003 escalade how to remove front bumper.


I just took this one on today. You'll need a flat head screw driver (a clip puller if you have one) a 15mm socket with a 10" extension and 10mm socket. Pop the hood, remove the plastic guard over the radiator and grill. Remove the 10mm bolt in the center of the grill. Remove the grill by popping the clips off each side then the grill will remove by pulling up. Remove the headlights by removing the two pins, one on top one on the inside of the lamp assembly. Remove 4, 15mm bolts from the top side of the bumper (2 upper, 2 lower that require the extension). From underneath the vehicle remove 2 more 15mm bolts (one from each side). The bolts are located just outside of the fog light assembly and sit horizontally. The bumper is now ready to be uncliped. From the inside of the wheel well use a Flathead screw driver to push in the clip while pulling the bumper away from the mounts. I used a large floor mat to keep the bumper from hitting the ground directly. It's helpful to have a second person to help on the last step.
Good Luck!

Aug 16, 2010 | 2004 Cadillac Escalade

2 Answers

How do I replace driver's side parking light? Directly below headlight. 2004 chevy tahoe.


you need to pull the pins holding in the headlight. push them out of the clip and then pull up once both are removed the headlight will come out and the parking lights/blinkers will come out also

Aug 02, 2010 | 2004 Chevrolet Tahoe

1 Answer

How do you take the grille off of a 1996 isuzu trooper 2




Trooper
See Figures 3, 4 and 5


a06490f.jpg
Fig. 3: Front grille assembly-1984-94 Trooper


e8688ea.jpg
Fig. 4: Front grille assembly-1995-96 Trooper


57fd329.jpg
Fig. 5: Retainer clip used to secure the front grille
  1. Raise the hood and support it with the prop rod.
  2. On 1981-94 models, remove the retainer screws from around each headlight.
  3. Remove the retainer screws from the corners and center of the grille.
  4. Using a small prytool to press the tab on each of the grille retainer clips at the top of the grille upward while pulling the grille away from the radiator support.
  5. When all the tabs have been released, lift the grille up slightly and out to remove.
To install:
  1. Engage the lower portion of the grille into the radiator support.
  2. Carefully push the grille toward the radiator support, making sure the retainer clips align with their respective mounting hole. Once all the holes align, press the grille and retainer in until it clicks into position.
  3. Install the retainer screws from the corners and center of the grille.
  4. On 1981-94 models, install the retainer screws around the headlight.

Hope helps (remember rated this).

Jul 09, 2010 | 1996 Isuzu Trooper

1 Answer

I need to take apart my 4unner grill


There will be one screw to undo, the rest is held in by clips , these are accessable from the front, using a flat bladed screwdriver lift the small tag protruding from the front of the clip, the grille will pop out ( one clip at a time) , leaving the clips behind in the radiator support panel, these come out with a twist and can be clipped back in to the grille before re-installation

Mar 28, 2010 | 1999 Toyota 4Runner

2 Answers

How do I change out a 2005 murano grille? THANKS


This is out of my 06 Murano manual, hope that it helps.

REMOVAL
1. Apply protection tape around outer circumference of front grille (bumper fascia side).
2. Remove front grille-radiator cover clips and remove front grille-radiator cover.
3. Remove clips on upper side of front grille.
4. Remove clips of air duct and remove air duct. Refer to EM-16, "AIR CLEANER AND AIR DUCT" .
5. Pull out grille pawls, and remove front grille assembly.

Installation is the reverse of removal.

good luck

Feb 26, 2010 | 2005 Nissan Murano

2 Answers

Grill removal


the lower clips are pushed down with a long screw driver from the front , when the grill is removed the clips need to be removed from the vehicle and put in the grill then push the grill in

Apr 18, 2009 | Mitsubishi Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...