Question about 2006 Opel Corsa Utility

Open Question

Location of the bcm on my utility

Left indicate not working

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you locate and test flasher relay on a 2006 Chevy Equinox? Turn signals and hazards stopped working after changing audio system. Fuses test good. Thank you, Mike


Did you change any wiring , tap into any wiring ? There is no flasher relay on your vehicle . It controlled by the BCM !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
Your best bet , take it to a qualified repair ! We on here have no clue what you did . On this newer vehicles ,if you know nothing about automotive electronics you really should take to a professional

Aug 10, 2017 | Cars & Trucks

4 Answers

Where is the signal relay located in a 2007 Pontiac G5 ?


https://s23.postimg.org/46g5rh3p7/flasher.jpg

Click on the link. The link should explain the operation.
There is no turn signal relay. At first I thought you meant the flasher, the flasher is incorporated into the bcm, no external flasher part, according to my info.

Jun 01, 2017 | Pontiac Cars & Trucks

1 Answer

I have 2008 chevy express, the turn signals flash fast, but not able to find a flasher unit. I have checked grounds, bulbs and fuses, all are good


The BCM - body control module controls turn signals . There is no flasher unit . Your best bet would be to take your vehicle to the dealer !
Turn Signal Lamps
The BCM 3, BCM 5, and BCM 6 fuses located in the underhood fuse block supply battery voltage to the body control module (BCM) for turn signal, hazard lamp, and stop lamp operation. Voltage from the BCM 5 fuse used for the front and rear left turn signals, voltage from the BCM 3 for the right front turn signal, while voltage from the BCM 6 fuse is used for the right rear turn signal. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G303 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.

Ignition ON, observe the scan tool Left Turn Signal Switch parameter while using the turn signal/multifunction switch to turn the left turn signal ON and OFF. The reading should change between Active and Inactive.

Apr 08, 2017 | 2008 Chevrolet Express

2 Answers

Where is the location for the relay turn signal 2007 cobalt


You won't find it because........there isn't one. The BCM (body control module) controls the flash. If you have no sound it could be a defective speaker.

Jul 01, 2016 | 2007 Chevrolet Cobalt Coupe

1 Answer

Why don't lights work?


Both the headlight switch and the BCM provide a ground, or control circuit, to the headlight relay coil circuit for manual or automatic headlamp operation. When you place the headlamp switch in the OFF position, and the ambient light sensor indicates low light conditions, the BCM energizes the headlamp relay for low beam operation. You may switch the headlights to high beam by pulling the dimmer switch handle toward you until the dimmer switch is activated. When the dimmer switch is placed in the HIGH position, the indicator lamp input to the BCM is pulled low. The BCM then sends a class 2 message to the instrument cluster in order to illuminate the high beam indicator lamp.
Low and High Beams Headlamps Inoperative ?
Replace the headlamp switch. Refer to Headlamp Switch Replacement .
Did you check the headlamp relay ? Location ,left instrument panel
Did

Nov 11, 2015 | 2001 Chevrolet Monte Carlo

2 Answers

Indicators, headlight, high beam, Heater showing strange behavior. Can you please suggest what could be the possible reason for it . BCM or Multi Function switch?


Hooking up an OBD2 reader will tell you right away if the BCM is shot or BCM. Take it to advanced auto or O'Riley's they will hook up a an OBD2 reader and tell you. Sounds like a faculty PCM and BCM to me or just faulty PCM since you've replaced the Body Control Module already.

Feb 20, 2015 | 2008 Hyundai Elantra

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

1 Answer

2010 chevy equinox right rear turn signal doesnt work, replaced bulb and still the same. front works, is there a fuse for the rear light and where is the fuse located.


RT/SIG fuse #11 15amp - I/P fuse box . Fuse Block - I/P
In the center of the instrument panel, beneath the right side of the radio, in back of the right side console access panel.
This fuse is power to the BCM , When you put on the right turn signal , this is a voltage signal to the BCM . With logic ( programming ) the BCM then controls the turn signal !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
There could be a DTC- diagnostic trouble code stored in the BCM pointing to the problem ! I suggest you take your vehicle to the dealer or a ASE certified repair shop that has the diagnostic tools to find the problem . Just so you don't waste your money replacing parts that don't fix it.
There could

Dec 14, 2012 | 2005 Chevrolet Equinox

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

Not finding what you are looking for?
2006 Opel Corsa Utility Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Opel Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Brad Brown

Level 3 Expert

15557 Answers

george parkes

Level 3 Expert

975 Answers

Are you an Opel Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...