Question about Dodge Ram 1500

1 Answer

Where is the heater core on a 2001 dodge ram 1500

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,113 Answers

Follow the 2 lines from your radiator where it goes through your firewall Probably behind your glove compartment

Posted on Nov 26, 2013

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 137 Answers

SOURCE: 2001 dodge ram 1500, blower

the blower resistor is the most likely reason.. for that truck you may also find that its melted and will require the pigtail for the resistor as well

Posted on Jan 21, 2009

  • 14 Answers

SOURCE: thermostat in 2001 dodge ram 1500

the thermostat is located where the upper radator hose comes off the engine there are two bolts or nuts remove hose and remove housing you will see the thermostat when you do clean old gasket material off block and reverse removal procedure

Posted on Apr 07, 2009

LEFTY64
  • 69 Answers

SOURCE: How to Replace a Heater Core

Removal & Installation

  1. Disconnect the negative battery cable.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument
  2. On diesel models, remove the passenger side battery and battery tray.
  3. Remove the instrument panel by performing the following procedures:
    1. Remove the air bag control module (ACM) and bracket from the floor panel tunnel.
    2. Remove the trim from both cowl side inner panels.
    3. Remove the steering column-to-instrument panel opening cover.
    4. Remove the 2 hood latch release handle-to-instrument panel lower reinforcement screws and lower the handle to the floor.
    5. Disconnect the driver-s side air bag module wiring harness connector from the lower instrument panel reinforcement.
    6. Place the wheels in the straight-ahead position and lock the steering wheel. Remove the steering column without disassembling it.
    7. From under the driver-s side of the instrument, disconnect or remove the following items:

      Parking brake release handle linkage rod from the parking brake mechanism located on the left cowl side inner panel. Instrument panel wiring harness connector from the parking brake switch located on the parking brake mechanism. Three wiring harness connectors (body wiring harness, headlight, dash) from the 3 junction block connector receptacles located closest to the dash panel. Head light/dash-to-instrument panel bulkhead wiring harness connector screw and disconnect the connector. Instrument panel-to-door wiring harness connector located directly below the bulkhead wiring harness connector. Infinity sound system wiring harness connector (if equipped), located at the outboard side of the instrument panel bulkhead connector. Stop light switch electrical connector. Vacuum harness connector located near the left side of the heater/air conditioning housing.
    8. Under the passenger-s side of the instrument panel, disconnect the radio antenna coaxial cable connector.
    9. Loosen both sides of the instrument panel cowl side roll-down bracket screws about 1 / 2 inch (13mm).
    10. Remove the 5 upper instrument panel-to-upper dash panel screws; remove the center screw last.
    11. Roll down the instrument panel and install a temporary hook in the center hole on top of the panel. Attach the other end to the center hole in the top of the dash panel. The opening should be approximately 18 inches (46cm).
    12. Disconnect the instrument panel-to-heater/air conditioning housing assembly wiring harness connectors.
    13. Using an assistant, remove the instrument panel from the vehicle.

  4. If equipped with air conditioning, perform the following procedure:
    1. Discharge and recover the air conditioning system refrigerant.
    2. Disconnect the refrigerant lines from the evaporator. Plug the openings to prevent contamination.
    3. Disconnect the refrigerant lines from the accumulator. Plug the openings to prevent contamination.
    4. Remove the accumulator.

  5. Drain the cooling system into a clean container for reuse.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Remove the PCM from the dash panel and move it aside. Do not disconnect the PCM harness connector.
  8. In the engine compartment, remove the heater/air conditioning housing assembly-to-chassis nuts.
  9. In the passenger-s compartment, remove the heater/air conditioning housing-to-dash panel nuts.
  10. Pull the heater/air conditioning housing assembly rearward far enough to clear the studs and air conditioning drain tube holes.
  11. Remove the heater/air conditioning housing assembly from the vehicle.
  12. Remove the upper-to-lower heater/air conditioning housing screws and remove the upper housing.
  13. Remove the heater core from the lower housing.


    Fig. View of the heater/air conditioning housing assembly


    0900c15280225dc3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. View of the heater core

Posted on Apr 08, 2009

  • 1 Answer

SOURCE: I have a 2001 1500 dodge ram it has no heat

are heater inlet outlet mix valves standard for all dodge heater cores. I have 2001 dodge cummings blows warm air not hot when gauge is 195 degrees would there be a mix valve under the dash because it is not inline outside the wall

Posted on Nov 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Dodge Ram 1500 truck smoke coming from vents


SEE IF YOU HAVE A SLIGHT OILY FILM ON THE INSIDE OF THE WINDSHEILD. IF SO THE HEATER CORE IS LEAKING

Dec 19, 2014 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How do I change out a heater core on a 2001 dodge ram 1500


AutoZone can print you out step by step instructions.

Sep 20, 2014 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

2001 dodge 1500 heat


Check if your rubber hoses that lead to the heater core have an inline valve. If the do, it sounds like it is not opening to allow circulation. normally they are vacuum operated

Nov 11, 2013 | Cars & Trucks

1 Answer

Can u flush out a heater core on a 2001 dodge ram 1500


yes you can flush the heater core I had to do that in my 2001 5.9 Ram and now I have a great deal of heat hope that helps

Oct 21, 2010 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

I have a 2001 1500 dodge ram it has no heat replaced heater core water pump thermostat radiator. I just blows warm air. what do I do now?


are heater inlet outlet mix valves standard for all dodge heater cores. I have 2001 dodge cummings blows warm air not hot when gauge is 195 degrees would there be a mix valve under the dash because it is not inline outside the wall

Nov 13, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

2000 Dodge RAM no HEAT/ New heater core / AC evap.


There is a actuator on the right side of your leg while sitting in the drivers seat under the dash. It has a plastic rod for actuation manually actuate this diverter and should be the problem.

Oct 14, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

MY HEATER CORE IS LEAKING IN MY 2002 DODGE RAM


You will have to remove a large portion of the dashboard. It is on the pasenger side, lower section.

Jun 23, 2009 | 2004 Dodge Ram 1500

1 Answer

I bypassed the heater core in my 2002 dodge ram 1500 and I just noticed coolant is still leaking in my passenger cab. What could be causing this?


Probably still some left in the heater core. Should quit after a while, or try blowing it out. I would even flush it with water first. Better to have water leaking than antifreeze. At least your dog can lick it and not die!

Jun 07, 2009 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...