Question about Cars & Trucks
Bad earth connection, take the earth cable off the battery and where it connects to the chassis, clean the connections and refit
Posted on Nov 27, 2013
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: wont start
If the solenoid makes a clicking sound it isn't the ignition switch. Depends on the clicking sound, one click or rattling. Try turning on lights and trying to start, if lights go out when attempting to start, voltage problem(usually battery or bad connections).
Posted on Nov 03, 2008
The Batt does not have a full charge or it is the wrong cranking AMP's for the car... find out if it is the right Batt and also that it is put on a "slow charge" over night or at least 6 hr's
Posted on Jan 20, 2009
you need to check for voltage drop in the wires you may have a bad wire bleeding to ground somewere that needs replaced also put a multimeter on the starter and make sure its gettting atleast 11 volts to it anything less and it wont turn hard enough
Posted on Oct 08, 2009
SOURCE: 98 Durango will not turn
Sounds like a bad
connection. Clean all the connections first then if you have a clicking sound
coming from the PDC (fuse box) on the drivers side under the hood then it
sounds like you have a bad starter .
As the relay is clicking that means the ignition switch is good. Just insure that the relay is good. There is a spare in the PDC you can swap and check out so its the starter Starter/solenoid combo.take your volt meter and check battery volts while the starter is engaged, if you see very little change from the static voltage it's likely the starter bendix is being egaged into the ring gear but the high current side of the starter is not working, this is likely due to a dirty or worn commutator or worn brushes in the starter motor. If you do see a larger drop in voltage( say down to under 9.5volts) you more than likely have a current flow issue, possibly a weak cell in the battery, or a shorted starter motor winding.My best recomendation would be to remove the starter motor, and the battery, take them in with you to your local parts house and have them both tested, most parts stores will perform these tests for free, on the possibility that hey can sell you something.
STARTER MOTORREMOVAL:-1. Disconnect and isolate the battery negative cable.2. Raise and support the vehicle.3. Remove the nut and lock washer securing the starter motor to the mounting stud on the transmission torque converter housing Starter Motor Remove/Install4. While supporting the starter motor with one hand, use the other hand to remove the upper mounting screw from the starter motor.5. Slide the automatic transmission cooler tube bracket forward on the tubes far enough for the starter motor mounting flange to be removed from the lower mounting stud.6. Move the starter motor towards the front of the vehicle far enough for the nose of the starter pinion housing to clear the transmission torque converter housing. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.7. Tilt the nose downwards and lower the starter motor far enough to access and remove the nut that secures the battery positive cable connector eyelet to the solenoid battery terminal stud. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.8. Remove the battery positive cable connector eyelet from the solenoid battery terminal stud. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.9. Disconnect the battery positive cable wire harness connector from the solenoid terminal connector receptacle. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.10.Remove the starter motor from the engine compartment. --This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya
Posted on Feb 22, 2010
Tips for a great answer:
Jul 07, 2014 | 2005 Hyundai Elantra
Dec 05, 2013 | 1998 Acura CL
Jul 05, 2011 | 2004 Mazda Tribute
Feb 14, 2011 | 2006 Dodge Charger
Jan 30, 2011 | Daewoo Leganza Cars & Trucks
Nov 11, 2010 | 2003 BMW 330
Dec 22, 2009 | 1996 Chevrolet Cavalier
Aug 12, 2009 | 2004 Dodge Neon
Jun 30, 2009 | 1999 Oldsmobile Alero
Mar 12, 2009 | 1999 Nissan Pathfinder
31 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: