Question about Cars & Trucks

1 Answer

Clio 2 needs a high level brake light.where can i find one

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,113 Answers

Here in Canada i can buy one at one of 30 or so places in my city. Canadian Tire is one such place I have no way of knowing what country or state etc you are in to give you specific store names. Ask a more detailed question telling us that info next time

Posted on Nov 26, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: High Level Brake bulb replacement

If memory serves, there are two screws holding this light assy to the rear package deck. They are covered (LH and RH side of this assy). remove the covers and using a phillips screwdriver, remove the screws and lift the assy up and away from the rear glass. you now have access to the bulb and socket.

Posted on May 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesn't the high level brake light work?


High level brake light is connected , in parallel with, all other brake/stop lights.. It is not on a separate fuse, so, check, or replace the other stop lights.
Or could be a bad ground on brake lights, but not on high level light.

May 02, 2015 | 1993 Honda Accord

1 Answer

My clio has shown fault codes df 135 and df 235 what do they mean


I've not had this indication myself, but a quick search found a similar part question about CLIOSPORTS car. In Apr 09 the following advice was given:
DF135 Brake pedal sensor circuit, signal incoherence - Memory
DF235: Cruise ctrl speed limiter, fault of the two brake pedal contacts
Advice: brake pedal switch (have a look in the guides, it just needs adjusting) also the cause of DF235.

So faults appear to be connected even if you do not have cruise control. I would have thought if your brake lights function that there should not be a problem.

Good luck

Aug 16, 2014 | 2002 Renault Clio

1 Answer

Warning sign of high level brake light


Please check your brake fluid and proceed immediately to a repair shop. If you don't know what the light means, you shouldn't mess with it yourself. The brakes are about the most important safety feature on your vehicle. Please call a mechanic.

Mar 28, 2014 | 2013 Porsche 911

1 Answer

Headlights not working on low or high beam


either main fuses under bonnet 60 amp for each side ir the light switch faulty ,also fuse in the interior fuse box but would have to blow around 6 all at same time so check the other first

Mar 01, 2014 | 2003 Renault Clio

1 Answer

Xj40 1993 jag. faulty high stop light operation spasmoticly misses


YOU HAVE A SHORT IN THE WIRING FROM THE REAR BRAKE LIGHT TO THE HIGH LEVEL BRAKE LIGHT , JUST FIND THE WIRING FROM HIGH BRAKE LIGHT TO LOW & REPLACE OR FIND THE SHORT & SPLIT THE CABLE REMOVE 5-8 MM OF SHEATH FROM EACH SIDE & CRIMP A CONNECTOR BRINGING THE TWO SEPARATE PIECES OF WIRE TOGETHER AGAIN

Sep 05, 2012 | 1994 Jaguar XJ6

2 Answers

Need to change brake light on a renault megane not the side brake lights but the tail light one, how do i get to it?


Hi
I presume you have a megane 2, this is the procedure.
How to remove the 3rd brake light.

1. Unclip the tailgate upper trim
2. Unclip the light by pressing on the lugs with a flat-blade screwdriver.
3. Unclip the screen washer jet by pressing the clips.
4. Disconnect the connector, Remove the high level brake light.

Refitting
Proceed in the reverse order to removal.

Note.
The vehicles are fitted with a brake light containing diodes.
I wouldn't recommend this unless you're planning in changing the whole unit.

I hope I have been somewhat helpful!

May 19, 2010 | 2004 Renault 181

1 Answer

Rear side brake lights won't work after fuses/bulbs replacement


If the high level brake lamp works and the other 2 lamps have good bulbs, then there is a power loss, most propably with the installation. You should go to an auto electrician to see where the break is.
If someone has recently done any work on the electrics, you should recheck. It is not a seperate fusable power supply system or brake switch for the high level brake lamp, it will take its power from the fused system that the other 2 have.
Hope this helps

Oct 04, 2009 | 1998 Land Rover Discovery

1 Answer

I have a Clio 172 sport but the rear brakes are not working, however the handbrake is fine? As all the braking is at the front of the car this is damaging the front discs?


Most of your braking occurs at the front of the car, anyways, but you need to get those rear brakes checked...

If you have a split (front-rear) master cylinder, check that. Did the fluid level drop enough at any time such that the system may have "sucked air" into the rear system only?

Mar 06, 2009 | Renault Le Car Cars & Trucks

1 Answer

Renault clio 2ltr sport back brakes


two brake shoes with a auto adjuster at the top ,handbrake lever on right shoe and two return springs .if you cant remember take the other side off and look at that

Feb 26, 2009 | 2003 Renault 181

1 Answer

Renault clio 2007 changing the front main lightbulb


it's a real nightmare to try to change it from inside..i tried and hardly succeeded on my clio campus 2007...yours is clio III, I suppose..so it should be the same system..you need a wrench tool of size 10 (mm)..and you will need to dismantle the front lapmp..don't worry..the level of the light beam is adjusted by the mechanism which is holding the light bulb in place, not the angle of the front lamp.

Dec 04, 2008 | 2006 Renault 181

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...