Question about Cars & Trucks

Open Question

Big end torque settings

IM NEEDING THE CONROD BOLT TORQUE SETTINGS FOR THE VW CRAFTER 2.5 TDI CEBB ENGINE

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
toddg
  • 171 Answers

SOURCE: need torque specs

Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees

Posted on Oct 14, 2008

Ad
  • 1779 Answers

SOURCE: internationl 345 v8 torque settings

Head bolt torque: 90-100 ft lbs., to be reached in 3 equal tightening steps, below is the sequence:
9 3 1 6 8
Front of vehicle
7 5 2 4 10

Main bearing cap torque: 75-85 ft lbs.
Rod bearing cap torque: 45-55 ft lbs.
Looks like u've been busy, and will be for a while. Good Luck!

Posted on Nov 16, 2008

  • 42 Answers

SOURCE: hi is there anybody who knows the torque settings

most local libraries has books with the specs in them

Posted on Mar 18, 2009

morse008
  • 1111 Answers

SOURCE: I need torque settings for 1600 beetle engine SP

wiki this

Posted on Aug 25, 2009

ZJLimited
  • 17970 Answers

SOURCE: hay there im rebuilding my

I would try the forum on the Daihatsu drivers club pages on the following page: daihatsu-drivers.co.uk

Check this information from the same site:

HEAD BOLT TIGHTENING SEQUENCE
OK, since I've got the book with me, I'll give you the head torquing sequence.
The best thing to do is to make a sketch of the head bolts as you look at the engine from the front of the vehicle.

There are 8 bolts outside the rocker box on the injector side of the head in a line from front to back. Starting at the front, label these bolts 14, 10, 6, 2, 3, 7, 11, and 15.

There are 5 bolts in line from front to back, directly under the rocker shaft. Starting at the front, label these bolts 17, 9, 1, 8, and 16.

There are 4 remaining bolts in the rocker box in line from front to back, above the exhaust and inlet ports. Starting from the front, label these bolts 13, 5, 4, and 12.

You have now drawn yourself a picture showing the tightening sequence for the head bolts.
---------------------------------------------------------------------
The torque setting is 117.7 +/- 9.8 Nm (Newton metres)
NOTE THAT BOLTS AND BOLT HEADS SHOULD BE OILED

To get foot pounds, multiply Nm by 0.738
I actually torqued my head to 70 Nm, then 95 Nm and finally 120 Nm.

Hope helps.

Posted on Dec 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

CYLINDER HEAD AND BIG END BEARINGS TORQUE SETTINGS FOR OPEL CORSA 2005 1.6LT PETROL MODEL SOUTH AFRICA


i think the 1.6 ltr was only for some markets the engine i think it may be is! cyl head head with new bolts, 25nm +90 +90 +90 + 45 degrees the big end/conrod bearings 25nm +30 degrees thats if it a vauxhall/general motors engine. it may not be

Sep 29, 2016 | 2005 Opel Corsa 1.6

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

CONROD TORQUE SPECIFICATION FOR 5A-FE ENGINE


ays as well as response to this question UVB the radiation. But it always recommended Vita Luminance while using safe sunscreen as per your skin sensitivity. Zinc oxide sunscreens are constructed from metallic zinc that recently been oxidised. It absorbs the UV rays and hence protects your skin from acquiring it contact with sun sun light.



http://utrimcleanseblog.com/vita-luminance/ Vita Luminance


Injection Free Solution For Youthful Skin

Jan 28, 2014 | 1991 Toyota Corolla

1 Answer

I need the Wheel Nut Torque settings for a 2009 VW Golf Estate 1.9 TDI


The wheel bolts torque settings for a 2009 VW Golf Estate 1.9 TDI is 120 Nm.

May 31, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

Flywheel torque setting vw transporter t30


VW Transporter 2.5 TDI-PD, (made year: 2003 ... 2007), engine code: AXD, 130 HP / 3500 rpm.
Important note: use new bolts!
Flywheel/driveplate torque setting: 60 Nm + 90 degrees.
Clutch to flywheel torque setting: 22 Nm.

May 21, 2010 | 2004 Volkswagen Eurovan

1 Answer

Engine torque settings VW lt 35 1993 2.4 turbo diesel. Code ACL


bob go to collsionrepairadvice.com and I will send the download to you its a big file

Mar 13, 2009 | 2000 Volkswagen Jetta TDI

3 Answers

Need torque specs


Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees

Oct 14, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...