Question about Cars & Trucks

Open Question

REQUIRE tORQUE SETTINGS FOR kOMATSU BULLDOZER D5015 A

Cylinder Head B.End, Small End Bolts and Exhaust Inlet & Outlet torque settings

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

Ad
inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder Head bolt torque and tappet settings to suit a , Ford Anglia 1964 105E Engine


Hi valve clearance inlet 0.010 in (0.254 mm). Exhaust 0.017 in (0.432 mm) normal running temperature .. Cylinder head bolts Torque 65 - 70 lb/ft.,.. Cheers

Jan 10, 2017 | Ford Cars & Trucks

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

I need the torque settings for toyota corola 1993 cylinder head torque please ?


Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

Mar 29, 2014 | 1993 Toyota Corolla

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

How to replace a waterpump on a 2001 olds alero 2.4 cam


Water pump is driven by timing chain idler and is mounted on the rear of the timing chain housing. Disconnect the neg. battery cable. Drain cooling system. Disconnect oxygen sensor connector.
Remove upper exhaust manifould heat sheild. Remove exhaust manifold brace. Remove lower exhaust manifold heat sheild. Loosen manifold to exhaust manifold spring loaded nuts. Remove radiator outlet pipe to water pump coverbolts. Disconnect exhaust pipe from manifold.
Pull down on the exhaust pipe to disconnect it from exhaust manifold bolts. Disconnect outlet pipe from oil pan and transaxle. If equipped with manual tranaxle, remove exhaust maifold brace. Leave lower radiator hose attached and pull down on radiator out look pipe to disengauge from water pump. Leave outlet pipe hanging.
Lower vehicle. Remove exhaustmanifold to cylinder head nuts. Remove exhaust manifold to cylinder head nuts. Remove manifould. Remove timing chain front cover. Remove timing chain tensioner. Remove bolts bolts securing water pump cover to cylinder block. Remove water pump to timing chain housing nuts. Remove water pump attaching nuts. Remove water pump and cover assembly. Separate componets as necessary.
WHEN INSTALLING WATER PUMP MAKE SURE YOU FOLLOW THE TIGHTENING SEQUENCES THAT AFFECT SEALING. My frist one I messed up and broke the pump so becarful.
Installation
If cover was separated from body during removal, join this componets with a new gasket and hand tighten bolts. Apply bearing grease to splines of water pump drive. Set body and assemble into position.
Install and hand tighten bolts securing cover to cylinder block. Install and hand tighten bolts securing cover to cylinder block. Installand hand tighten nuts securing body to timing chain housing. Lubracate outlet pipe "O" ring with antifreeze. (I use RTV) Connect outlet pipe. Install and hand tighten bolts. Tighten bolts and nuts to specification in the following sequence. I'll ad the torque spec. at the end but this is where if you tighten out of order something will break.
pump assembly to timing chain housing nuts.
pump cover to pump body bolts
pump cover to cylinder block bolts (Bottom Bolt First)
outlet pipe to cover bolts
To complete installation reverse removel procedure.
Torque specs are 19 in. or 26mm all except water pump cover bolts which are 124 in or 14Nm
I never torque the bolts just make sure there done in the right order.

Oct 19, 2010 | Oldsmobile Alero Cars & Trucks

3 Answers

How do I remove the head? (Blown Head gasket)


prev.gif next.gif Cylinder Head REMOVAL & INSTALLATION 2.3L Engine
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable, then drain cooling system into a suitable container.
  3. Detach the heater inlet and throttle body heater hoses from water outlet. If accessible at this time, disconnect the upper radiator hose from the water outlet.
  4. Remove the exhaust manifold. For details, please refer to the procedure located in this section.
  5. Remove the intake (camshaft housing for SOHC) and exhaust (DOHC only) camshaft housings.
  6. Unfasten the oil fill tube bolt/screw then remove the oil fill cap and level indicator assembly. Pull the oil fill tube upward to unseat from block.
  7. Label and disengage the injector harness electrical connector.
  8. Detach the throttle body-to-air intake duct.
  9. Tag and disconnect the power brake vacuum hose from the throttle body.
  10. Remove the throttle cable bracket.
  11. Remove the throttle body from the intake manifold with the electrical harness and throttle cable attached and position the assembly aside.
  12. Tag and disconnect the MAP sensor vacuum hose from the intake manifold, then remove the intake manifold brace.
  13. Detach the electrical connectors from the MAP sensor, IAT sensor and the EVAP canister purge solenoid.
  14. If not already done, detach the upper (inlet) radiator hose from the water outlet.
  15. Disengage the coolant temperature sensor connector(s).
  16. Unfasten the cylinder head bolts in reverse order of the installation sequence shown in the accompanying figures.
  17. Lift the cylinder head from the engine block. Remove and discard the gasket. Inspect the oil flow check valve for freedom of movement.
  18. Using a suitable solvent, thoroughly clean and dry all bolts, bolt holes and mating surfaces. Inspect the head bolts for any damage and replace, if necessary. If using a scraper to clean the old gasket material from the mating surfaces, use only a plastic or wood one, NOT a metal scraper. Do NOT allow any debris to fall into the engine! To install:
  19. Place a new cylinder head gasket on the cylinder block, then carefully position the cylinder head in place.
  20. Sparingly coat the head bolt threads with clean engine oil, then allow the oil to drain off before installing.
  21. On 1988-89 engines, install and tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 80°and the long bolts an additional 90°in sequence Fig. 5: Cylinder head bolt tightening sequence - 1988-89 2.3L engine 86883121.gif
  22. On 1990-91 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 100°and the long bolts an additional 110°in sequence Fig. 6: Cylinder head bolt tightening sequence - 1990-91 2.3L engine 86883122.gif
  23. On 1992 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten, in sequence, head bolts 1-6 to 26 ft. lbs. (35 Nm), 7-8 to 15 ft. lbs. (20 Nm) and 9-10 to 22 ft. lbs. (30 Nm).
    • Step 2 - Tighten all head bolts, in sequence, an additional 90°using J 36660 or equivalent
    • Step 3 - In sequence, loosen each bolt one turn, then immediately re-tighten to the specified torque
    • Step 4 - After completing step 3 on all 10 bolts, tighten each bolt, in sequence, an additional 90° Fig. 7: Cylinder head bolt tightening sequence - 1992 2.3L engine 86883123.gif
  24. On 1993-95 vehicles, tighten the cylinder head bolts to the specifications shown in the accompanying figures. Fig. 8: Cylinder head bolt tightening sequence and specifications - 1993 2.3L engine 86883124.gif
    Fig. 9: Cylinder head bolt tightening sequence and specifications - 1994-95 2.3L engine 86883125.gif
  25. Engage the coolant temperature sensor electrical connector(s).
  26. Connect the upper radiator hose to the water outlet.
  27. Install the intake manifold bracket.
  28. Attach the following electrical connections: MAP sensor, IAT sensor, and the purge solenoid.
  29. Using a new gasket, install the throttle body to the intake manifold.
  30. Install the accelerator control cable bracket.
  31. Connect the throttle body-to-air intake duct.
  32. Install the oil fill tube and level indicator.
  33. Install the camshaft housing(s).
  34. Install the exhaust manifold. For details, please refer to the procedure located in this section.
  35. Connect the heater inlet and throttle body heater hoses to the water outlet.
  36. Fill all fluids to their proper levels.
  37. Connect the battery cable, start the engine and check for leaks.

Sep 24, 2010 | 1992 Oldsmobile Achieva

1 Answer

Blown head gaskit need to remove head and replace with new ong


2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Accessory drive belt
    • Air cleaner outlet duct
    • Engine mount
    • Intake manifold
    • Exhaust manifold
    • Engine Coolant Temperature (ECT) sensor electrical connector
    • Power steering pump
    • Radiator inlet pipe
    • Spark plug wires
    • Rocker arm cover

    NOTE Whenever valve train components are removed, keep them in order for installation purposes.

    • Rocker arms and pushrods
    • Lifters
    • Alternator rear brace and the alternator
    • Power steering pump
    • Radiator inlet pipe
    • Ignition coil assembly
    • Accessory bracket
    • Spark plug wires
    • Cylinder head bolts

    WARNING Two sizes of bolts are used; note the location of each.

    • Cylinder head
  5. Inspect the cylinder head and block surface for cracks, nicks, heavy scratches and flatness.
b9d2546.gif
Cylinder head torquing sequence—2.2L (VIN 4) engine

  1. Install or connect the following:
    • Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.
    • Lifters
    • Pushrods and rocker arms. Torque nuts to 22 ft. lbs. (30 Nm).
    • Rocker arm cover. Torque the bolts to 89 inch lbs. (10 Nm).
    • Spark plug wires
    • Accessory bracket
    • Ignition coil assembly
    • Radiator inlet pipe
    • Power steering pump. Torque the bolts to 22 ft. lbs. (30 Nm).
    • ECT sensor electrical connector
    • Exhaust manifold. Torque the nuts to 118 inch lbs. (13 Nm).
    • Alternator. Torque the bolts to 37 ft. lbs. (50 Nm).
    • Intake manifold. Torque the bolts to 17 ft. lbs. (24 Nm).
    • Engine mount. Torque the bolts to 55 ft. lbs. (75 Nm).
    • Air cleaner outlet duct
    • Accessory drive belt
    • Negative battery cable
  2. Refill and bleed the cooling system.
  3. Start the vehicle and inspect for leaks.

Oct 08, 2009 | 2000 Chevrolet Cavalier

1 Answer

Escort Mk2 1600 valve and torques settings what are they


cylinder bolt torque settings stage 1 15 ft pounds
stage 2 50 ft pounds
stage 3 85 ft pounds

valve clearences 0.15 - 0.20mm inlet
0.22 - 0.27mm exhaust
these are the figures i have been supplied with, you can also use

cylinder bolts stage 1 10 ft pounds
stage 2 50 ft pounds
stage 3 + 90deg.
with my exp, i would use the first guide as the degree method has a tendancy to snap head bolts, especially on older vehicles.

May 12, 2009 | Ford Escort Cars & Trucks

1 Answer

Differential Torque settings for 2003 Town Car


New cylinder head bolts are required and an angle guage,or you can make one up with card and a set square. Head bolt torque is 25Nm(newton metres)+60degrees + 60deg + 60 deg so it's a four step process.Con.rod bolts(big-end)28Nm,Inlet manifold 28Nm,Exhaust manifold 25Nm, Crank pulley 40Nm,Sump 5Nm and use locking compound (loctite)Timing cover 6Nm. Valve clearance,set inlets to .006" and ehausts to .010"(set approx.when cold then re-adjust while warmed engine is idling.

Feb 20, 2009 | 2003 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...