Question about Hyundai Accent

1 Answer

I have a 2003 Hyundai accent, i just got a new clutch, but when i shift, it grinds between 1st, 2nd and now 3rd, and yes im shifting it right, what could it be and how much

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

CHECK SHAFT TIMONERY ! USUALLY THERE ARE NUTS PROBLEM (PLASTIC)

Posted on Nov 26, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: automatic transmission shifts hard and

have u checked the tranny fluid

Posted on Oct 06, 2008

alicantecoli
  • 22219 Answers

SOURCE: hard shift from 1st to 2nd gear automatic

what year is vehicle please ?? as people often put it in wrong catagory ,if its mazada 2007 then its dealer only as a computer controls it all and the software is factory encrypted to stop general garages from repairing it .But check for a vacumn pipe loose under bonnet ,thin rubber pìpe from inlet manifold to gearbor or a diaphram switch,

Posted on Feb 19, 2009

  • 1 Answer

SOURCE: It's an automatic but it won't shift from 2nd to 3rd.

I would have to say it is the tranny check the fluid make sure it is clean and at the correct level

Posted on Apr 16, 2009

SOURCE: transmission won't shift to 2nd and 3rd gears goes from 1st to 4th.

Doesn't sound like a simple fix. I would suggest having it serviced.

Posted on May 05, 2009

citroenchris
  • 600 Answers

SOURCE: on my 1976 Triumph TR6 when shifting I get a

Have you checked the end float on the cranK, try pulling and pushing the pulley on the crank, those engines were famous for wearing the thrust washers and then they drop out they take the "push" from the clutch release mechanism and if the play is too big it causes drag.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would be the problem with gwm steed 2.2 when shifting first 2 gears that it scratches


what do u mean scratching that is a new word for me ,if you mean grinding sounds like the clutch is going bad if it it a stk ,and it is not depressing all the way ck your brake fluid in your clutch resivoir

Dec 03, 2014 | Cars & Trucks

1 Answer

I bought a 1998 Saturn SL1. During the 1 month warrenty I noticed the car would not down shift into 2nd gear. The dealership did some work on the drivetrain and then it would downshift into second. But...


Check the fluid level in you slave cylinder. If the fluid is low or there is air in the system it can cause hard shifting. If everything is ok it is problably the syncros.

May 06, 2014 | Cars & Trucks

1 Answer

I have a 2003 hyundai accent, it has 74000km and i just got a new clutch, but when i shift, it grinds between 1st, 2nd, and 3rd, what could it be, and how much will it cost to fix?


your clutch needs adjusting again yours would probably be hydraulic so it will need some bleeding at the cylinder however should it be cable it will need some adjusting

Nov 26, 2013 | Hyundai Accent Cars & Trucks

1 Answer

Overdrive


Probably a shift solinoid in the gear box. My commodore has 2 (1st & 2nd) & (3rd & 4th) my 3 / 4 solinoid went so went 1st 2nd 3rd but not to 4th until I replaced it.

Jun 15, 2012 | 2000 Hyundai Accent

1 Answer

Was shifting from 2nd to 3rd gear when shift lever got loose,chould not shift into any gear,seems like it is stuck in 1st now.Feels like I still have clutch,could it be something in the linkage


Sounds like you broke your linkage. It's not as bad as it sounds. It's a cable, or a small plastic part. It will be expensive to have a shop do it. Try to get help from a friend.

May 11, 2011 | 2003 Hyundai Santa Fe

2 Answers

Grinding gears from 1st to 2nd, 3rd to 5 ok


Either your clutch is getting bad, or you're shifting down too soon, and up too late. Try double clutching. Push in your clutch and push it into neutral. Release the clutch, fan the gas pedal, push the clutch again and shift into 1st. All this does is sychronize the speed of the transmission with the speed of the engine. There were, in the 60's, a lot of cars with the old "three on the tree" that you had to do this every time, and you get pretty good at it after a while.

Jun 02, 2009 | 1995 Hyundai Sonata

1 Answer

My 92 honda accord will not go into 1st 3rd or 5th gear


check shift fork adjustment. make sure you bleed the slave cylinder.also check shift cable adjustment.

Apr 11, 2009 | 1992 Honda Accord

4 Answers

DASH LIGHT CAME OFF


there are a couple of diodes under the hood that need changing at about 12 dollars each.should solve your problem

Jul 12, 2008 | 2001 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...