Question about GMC Yukon Denali

Open Question

Flashing oil change light 01 yukon - Yukon Denali GMC Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Pontiac service light 1983-01


Firebird

1998-01

To reset the "CHANGE OIL" light, press and hold the "TRIP/OIL RESET" button on the instrument panel for 12 seconds. When the light flashes and goes out, the system is reset.


Grand Am


1999 -01

To reset the Change Oil light, open the driver's side instrument fuse panel and turn the ignition on. Press the "RESET" button and release. The light will flash. Press the button again and the system will be reset.


Grand Prix


1999-01

Driver Information Center If Equipped). Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHANGE OIL SOON indicator flashes two times, the system is resetting. Turn the ignition key to OFF, then start the vehicle. If the CHANGE OIL SOON indicator comes on and stays on, repeat the procedure. To reset the OIL LIFE indictor if equipped with a Trip Computer: Press the trip MODE button until the light appears next to OIL LIFE. Press and hold the trip RESET button until the oil life percentage changes to be 99 percent.


Grand Prix


1997-98

To reset the oil life indicator, press the "MODE" button until the light next to "OIL LIFE" is lit. Press and hold "RESET" for 3 seconds until oil life percentage is 100%.


Grand Prix SE


1997

Turn the ignition on, but do not start the vehicle. Within 5 seconds, push the accelerator to the floor 3 times. Turn the ignition off. Start the car and the Change Oil Soon indicator light will be reset.


Grand Prix

w/ Trip Computer

1988-93

To reset "CHANGE OIL", "CHANGE OIL FILTER", or the mileage of either on the Trip Compute, continually press the "SERVICE" or "SYSTEMS CHECK" button until the item appears with the mileage below it. Then press the "RESET" button and the mileage will be reset to the maximum value. If you want to reduce this value, hold the "RESET" button down and the mileage will count down. Release the button at the mileage you would like to observe.


Bonneville,
6000

w/ Driver Information Center

1983-91

To reset "CHANGE OIL SOON" or "OIL FILTER" or to adjust the mileage on the Driver Information Center, continually press the "DIC" button until either message appears with the mileage below it. At this point, hold down the button. In 5 to 10 seconds, the mileage will count down. When it passes 0, it will cycle back to a maximum figure. Release the button when the mileage gets to the service interval you'd like to observe. If "CHANGE OIL" or "OIL FILTER" already appears, just hold the button down to reset the mileage. "CHANGE OIL" and "OIL FILTER" are reset separately.













on Dec 07, 2009 | Pontiac Grand Prix Cars & Trucks

Tip

Oldsmobile service light 1991-01


Alero

2000-01

Turn the ignition to the ON position, engine OFF. Press the RESET button and release. The CHANGE OIL indicator will start flashing
2000: Press and release the RESET button again.
1999: Press and hold the RESET button until an audible chime is heard and then release the button.


Intrigue


2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHANGE OIL SOON indicator flashes two times, the system is resetting. Turn the key off after the the light has finished flashing, then start the vehicle. If the CHANGE OIL SOON indictor comes back on, the engine oil life monitor has not reset. Repeat the procedure again. If the vehicle is equipped with the U20 option code, the vehicle as an oil life low indicator. The oil life low indicator shows an estimate of the oil's remaining useful life. When the oil life index is less than 10 percent, the display will show OIL LIFE LOW. To reset the oil life monitor, press and hold the MODE button until the light appears next to OIL LIFE. Press and hold the trip RESET button until the oil life percentage changes to 99 percent.


Alero,
Intrigue,
Cutlass Supreme


1999,
1998,
1996-9

To reset the "CHANGE OIL" light, turn the ignition switch to the "RUN" position with the engine off. Fully depress and release the accelerator pedal three times in five seconds. The light will flash twice and go out.


Aurora


1995-99

To reset the "OIL LIFE" message, press the "ENG" button with the ignition on until "OIL LIFE PERCENTAGE" is shown. Press the "RESET" button for 5 seconds. "RESET" will appear and then "OIL LIFE" will show 100%


Eighty-Eight,
Ninety-Eight,
Regency


1994-97

When "CHANGE OIL NOW" is displayed, press the "RESET" button. Press "SEL" to display "OIL". Press "SEL" to display oil life. Press and hold "RESET" for 5 seconds. A "RESET" message should display with oil life changed to 100%.


Eighty-Eight,
Ninety-Eight


1992-93,
1991-93

Press and release the "TEST" button on the Driver Information Center. This will illuminate "CHANGE OIL NOW" if it is not already illuminated. Press and release the "OIL" or "OIL INDEX" button. Next, press the "RESET" button and hold for at least 7 seconds.


Toronado,
Trofeo

w/o CRT Display

1991

To reset "OIL LIFE INDEX", press the "2 OPTIONS" button: three times if the vehicle is equipped with a phone and compass, once if equipped with neither. While "OIL LIFE INDEX" is displayed, press and hold the "RESET/ENTER" key at the bottom right of the 15 button switch for 5 seconds.













on Dec 07, 2009 | Oldsmobile Alero Cars & Trucks

2 Answers

My 2001 yukon xl dash is reading, "check oil pressure when i crank it up. the oil level is at zero. do you have any idea what it is? before this hapeened the check engine oil level light flashed on...


well so if i understand right you have no oil in the vehicle? or have you checked the oiil dipstick, GM is known to burn oil so if you go alot more than three thousand miles between oil changes than that will cause the oil to burn off and cause the lights to come on, or you might have a leaky filter or drain plug and its loosing oil, so first pull he diptick check level and if you need oil just go get an oil change and they snould let you know of any leaks there may be

Aug 31, 2011 | 2001 GMC Yukon XL

2 Answers

How do I reset oil life low light?


This one should be turn the key on to run position and fully depress the gas pedal 3 times within 5 seconds, If done correctly the light should start flashing.

Nov 27, 2010 | 1999 Buick Regal

Tip

Chevrolet service light 1991-01


Camaro

1998-01

To reset the "OIL CHANGE" light, press and hold the "TRIP/OIL RESET" button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset.


Corvette


1997-01

To reset the monitor after an oil change, turn the ignition on. Press the "TRIP" button so that the "OIL LIFE" percentage is displayed. Press "RESET" and hold it for two seconds. The word "RESET" should appear on the monitor, then "OIL LIFE 90%".


Impala,
Monte Carlo


2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator three times within five seconds. If the CHG OIL SOON lights two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not been reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to exit programming. A chime will be heard to verify the exit.


Impala,
Caprice


1994

To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Access the reset button on the end of the instrument panel by the fuse block. Press the switch and hold it for at least 5 seconds.



Lumina,
Monte Carlo,
Impala,
Caprice


1996-00,
1996-99,
1995-96,
1995-96

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds. The light will flash and go out.


Corvette


1990-96

After an oil change, or when "CHANGE OIL" appears on the Trip Monitor, with the ignition on and engine off, press the "ENG MET" button (located on trip monitor) once. Press the "ENG MET" button again within 5 seconds. Within 5 seconds, press and hold the "RANGE" button (1990-1994) or "GAUGES" button (1995). The light will flash. When it stops flashing and goes out, the system is reset.


Chevrolet Suburban,
GMC Yukon XL,
Chevrolet Silverado,
GMC Trucks Sierra


2000-01,
1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.


Silverado, Sierra Trucks


1991-93

To reset the "CHANGE ENGINE OIL" message, turn the ignition key to the run position. Press and release the accelerator pedal three times within 5 seconds. If the light flashes for 5 seconds, the system is reset. Repeat procedure as needed.















on Dec 07, 2009 | Chevrolet Camaro Cars & Trucks

Tip

Buick service light 1991-01


LeSabre,
Park Avenue


2000-01

Turn the ignition to ON. Press the GAUGE INFO button on the driver information center (DIC) switch to view OIL LIFE INDEX. Press and hold the RESET button on the DIC until the display reads OIL LIFE INDEX 100% NORMAL. The engine oil life monitor is now reset. Turn the ignition OFF.



Park Avenue


1997-99

When "OIL LIFE INDEX CHANGE OIL" appears in the Driver Information Center, press and hold the "RESET" button while the oil life index is being displayed. After 5 seconds, the oil life will change to 100%



Le Sabre,
Park Avenue


1995-99
1995-96

When "CHANGE OIL SOON" light is illuminated, access the reset button in the glove box. With the engine off and the ignition switch in the run position, press and hold the button for at least 5 seconds. The light will flash four times and then go out.



Century,
Regal,
Roadmaster


1997-01,
1996-01,
1995-96.

To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Fully depress and release the accelerator pedal three times within 5 seconds. The light will flash twice and go out.



Roadmaster


1994

To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Access the reset button on the end of the instrument panel by the fuse block. Press the switch and hold it for at least 5 seconds.



Le Sabre,
Park Avenue


1992-94,
1991-94

When "CHANGE OIL SOON" light is illuminated, find the hole in the underside of the dash on the passenger side near the door. Insert a blunt instrument into the hole and press the switch. The light will flash four times when the system is reset.











on Dec 07, 2009 | Buick LeSabre Cars & Trucks

1 Answer

How do you reset oilchange light on a 2001 yukon xl


turn key to on position, pump gas pedal to floor 5 times and turn off key. start vehilce. Change oil light should flash for 7 seconds and then go out.

May 15, 2010 | 2001 GMC Yukon XL

1 Answer

How to reset oil change light?


Make and Model: Chevrolet Suburban, GMC Yukon XL, Chevrolet Silverado, GMC Trucks Sierra
Years: 2000-01, 1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

Hope this help (remember rated and comment this help) Good luck.

May 14, 2010 | 1999 GMC Sierra

1 Answer

How do you reset oil change indicator?


Chevrolet Service Light - For Chevrolet Suburban, GMC Yukon XL, Chevrolet Silverado, GMC Trucks Sierra 2000-01 and 1999-00:

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

I really hope helps with this (remember rated this help) Good luck.

Jan 05, 2010 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...