Question about Toyota Camry
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
To program a remote... note that you must not delay more than 10 seconds between any of the operations.
Driver's door open, all other doors closed, key removed from the ignition switch.
Insert key into ignitions switch, then remove it.
Press LOCK then UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.
close and re-open drivers door.
Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times
Insert Key into ignition switch.
Switch ignition ON and OFF once to program a remote transmitter code while retaining the original codes or twice to program a remote transmitter code while erasing the original codes. three times to check how many remote transmitters are currently registered, or 5 times to erase all registered codes.
Remove Key from ignition switch.
System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. It will lock and unlock one to four times slowly, to indicate the number of remote transmitters registered if you chose option 3.
Press and hold remote transmitter LOCK and UNLOCK buttons at the same time.
Press LOCK remote button for 1 second: System should now lock and unlock vehicle once to confirm, twice to indicate registration has failed.
NOTE: to exit programming mode, close drivers door or insert key in the ignition.
NOTE: a maximum of 4 remote transmitters can be programmed
Posted on Oct 13, 2008
Under the engine in the front you will see an aluminum cover.There is a square hole that fits a 3/8 ratchet remove this first.The new filter comes with a drain adapter that snaps in the hole under the cover.This lets the oil in the housing drain.Then take a oil filter cup wrench or a big channel lock to twist of the larger portion.Then change the filter and o-ring and reinstall.Make sure the o-ring on the square drive cover is there also
Posted on Nov 30, 2008
Hi I'm litoshop if the security light stop blinking.then you deactived the alarm if your car has a factory alarm then the same light you see blinking look at it close and see if it's a switch push it in and put the key on and just turn on the dash light then turn it off the it should start blinking agian if it's not the light the look for a small red push botton and do the same as instructed above good luck. if this information has been useful please let us know thank you...
Posted on Aug 02, 2009
sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!
Posted on Aug 20, 2009
all keys/car have to be programmed at the same time.using nissan diagnostic machine.you could try a quickfit centre (if they have correct machine)
Posted on Feb 17, 2010
Tips for a great answer:
Apr 23, 2015 | 2012 Toyota Camry
Sep 28, 2013 | 1995 Toyota Camry
Jul 19, 2013 | 2007 Toyota Camry
Sep 22, 2012 | 2009 Pontiac Vibe
Sep 02, 2012 | 2002 Toyota Camry
Jun 01, 2012 | 2009 Volkswagen Passat 2.0
Nov 04, 2010 | 1995 Toyota Camry
Jul 10, 2010 | 2009 Toyota Camry
Aug 02, 2009 | 2000 Toyota Camry Solara
Jul 17, 2018 | Toyota Cars & Trucks
229 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: