Question about Jeep Cars & Trucks

Open Question

Jeep Compass Code P0722

2011 Jeep Compass 4x4, just changed the Crank Position Sensor, and now I get an error code of P0722

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Jeep Hesitates. P0303 code

Check the cylinders Commpression. over 115 psi is good, 120 psi is normal.

Posted on Sep 17, 2008

  • 383 Answers

SOURCE: jeep wrangelr Crank Position Sensor

wall5552: there were two engines used in 1992 Jeep Wranglers.
A 2.5 liter and a 4.0 liter. HOWEVER>>>> The location for the crank angle sensor is the same for both.
It is located on the bell housing up near the front at about the 10:00 PM position.
The Cam position sensor is located in the Distributor on both engines as well.

Posted on May 10, 2009

  • 4044 Answers

SOURCE: 1999 chrysler 300m wont crank, code P0340

Sounds like the timing belt broke. Unfortunately this vehicle was not equiped with no contact valves so if that is the case you will need to have the engine and Head rebuilt. If the crank position sensor can't sense the position of the crank it should shutdown the electrical to keep you from damaging your engine.

Posted on Oct 09, 2009

johnjohn2
  • 5763 Answers

SOURCE: 2003 Jeep Liberty Stalls

thats correct, may have bad ecm (computer) or bad wire to crank sensor from ecm, also ive run into this problem and it was the new sensor i put in was no good and aftermarket,also cam sensor can do this, and also make sure the 5 volt feed wire is good,good luck hope this helps.

Posted on Oct 13, 2009

Testimonial: "It ended up being the cam sensor. Thanks for the info. Fixed it right up."

mikestoys32
  • 37 Answers

SOURCE: Jeep is giving a code of p0340 which is telling me

go to autozones website they have free diagrams

Posted on Dec 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I solve a problem on my 2013 jeep compass with error code p161b


I use a software called autodata and there is no P161b code listed.
I did find
P016b- closed loop mixture control , limit reached - system too rich
P0161- heated oxygen sensor bank 2

Jun 03, 2017 | Jeep Cars & Trucks

2 Answers

What are diagnostic codes: c1044 and p0707


C1044-RIGHT REAR TONE WHEEL PERFORMANCE
P0707 - Transmission Range Sensor Circuit Low Input Possible causes
- Faulty Park/neutral position switch
- Misadjusted park/neutral position switch
- Park/neutral position switch harness is open or shorted
- Park/neutral position switch circuit poor electrical connection

Apr 07, 2015 | 2007 Jeep Compass 2.4

1 Answer

2002 jeep grand cherokee diagnostic trouble code P 0320? how do i repair?


No Crank Reference Signal at PCM No reference signal (crank-shaft position sensor) detected during engine cranking. Use this youtube step-by-step to fix it. How to diagnose P0320 crankshaft position sensor circuit failure

May 01, 2014 | 2002 Jeep Grand Cherokee

2 Answers

I have a 2002 Jeep Grand Cherokee. I am getting a bad crank shaft sensor/misfire error code. I have replaced the crank shaft sensor, spark plugs and coil but the problem stiil remains. What else could...


Your engine will also have a Camshaft position sensor too (P0340). This can sometimes make the Crankshaft sensor code come on (P0335). Your misfire could be down to a low oil level or faulty knock sensor. You have ruled out the possibility of it being a spark related issue. Hope this helps...

Mar 10, 2011 | 2002 Jeep Grand Cherokee

2 Answers

Need to change camshaft position sensor 2007 Jeep compass 2.4 eng


Jeep Patriot Crankshaft Position Sensor replacement ...

? 9:09
https://www.youtube.com/watch?v=omwDHaBGUEc
Jan 15, 2012 - Uploaded by JasonthePCMD
Here's how to replace the Crankshaft Position Sensor (CKP) on a 2008 and newer Jeep Patriot, Compass ...

Jeep Cherokee camshaft crankshaft sensor how to replace ...

? 2:59
https://www.youtube.com/watch?v=oOc1Lxod2x8
May 17, 2012 - Uploaded by unpescad0
How to locate and install a new camshaft and or a crankshaft position sensor. This vehicle is a 2001 Jeep ...

Crankshaft position sensor location - Jeep Patrio



Sep 14, 2009 | 1996 Dodge Caravan

2 Answers

Jeep is stalling every now and then. engine code: p0320 engine speed input malfunction. Changed crank angle censor but problem still persists. it has been in the workshop almost two weeks, no one can find...


The code refers to the crank position sensor. The Crankshaft Position Sensor (CKP) is mounted to the transmission bellhousing at the left/rear side of the engine block.

Nov 03, 2008 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...