Question about 2004 Chevrolet Colorado

1 Answer

Reset bcm colorado - 2004 Chevrolet Colorado

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 32 Answers

Leave batt. Disconnected 15-20 min.

Posted on Nov 26, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disconnect a BCM in a chevy colorado 2007


Removal Procedure
Important:
• The ignition switch should be in the OFF position when connecting or disconnecting the connectors to the body control module (BCM).
• Always disconnect the black body wiring harness connector FIRST and the gray instrument panel (I/P) wiring harness connector LAST.
• Always connect the black body wiring harness connector FIRST and the gray I/P wiring harness LAST.
• Do not open the BCM housing. The module does not have any serviceable components. The module may be replaced only as an assembly.
Ensure the ignition switch is in the OFF position.
Remove the right front hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side .
Disconnect the body wiring harness electrical connector (1) from the BCM.
Release the fastener retaining the body wiring harness electrical connector to the BCM. Remove the 2 fasteners retaining the BCM to the hinge pillar.
Remove the BCM from the hinge pillar by unlocking the integral tab.
Remove the BCM from the vehicle.
If installing a replacement BCM, program the BCM. Refer to Control Module References .

Dec 19, 2016 | Cars & Trucks

1 Answer

Chevy colorado electrical


problem could be the door switch or bcm let dealership check it out.not much you can do.most newer vechicles everything control by BCM and PCM.

Jul 10, 2013 | Cars & Trucks

2 Answers

How do you reprogram your BCM on a 2006 Chevrolet Colorado


Sounds like the BCM is either defective or needs reprogramming. Since you are combining 3 trucks, were all working well before they became parts vehicles? In a collision, the electric wiring to the BCM may have been smashed and with "crossed" wires may have been erased or shorted.

You would swap BCM's and use the driveable one to get to the Dealer for reprogramming or Autozone, Advace, or Oreilys for a free scan.

Sep 09, 2012 | 2006 Chevrolet Colorado

1 Answer

Where can I find the wiring diagram for this Chevy Colorado 2007 for the Speedometer. I bought this Truck to this local Car Dealer with Speedometer doesn't function at all. I want to try to see what...


Your speedometer is controlled by your computer network. The vehicle speed sensor (VSS) sends a signal to the Body Control Module (BCM) which then relays the speed sensor data via the UART data lines to the Powertrain Control Module (PCM) and the Instrument Panel Cluster (IPC). To find out why your speedometer is not functioning, you must FIRST scan your ENTIRE computer network for possible fault codes. It is possible that either the VSS is defective or the BCM is not able to relay the information due to a communications fault, or the BCM is relaying the information and the IPC is unable to receive the information due to a communications fault, or the IPC itself is defective. Wiring diagrams will be of no use until you determine which parts of the network is receiving the information from the VSS and which parts are not. This will require the use of a scan tool that can not only read generic OBD fault codes, but also access and display codes and live data from the BCM, PCM and IPC.

Oct 21, 2011 | 2007 Chevrolet Colorado (Extended Cab) New...

1 Answer

... Replaced battery in a 2005 Chevy Colorado Crew


something puts bcm into safe mode. take neg. battery cable off and touch it to pos. post for 30 sec. leave unconnected for 6 hrs then reconnect. should work after that. just did mine. dealer wanted 400$ to change door switch

Feb 16, 2011 | 2005 Chevrolet Colorado

1 Answer

2005 chevy colorado battery went dead and when i rechanged it the drivers door window would not go up or down the other 3 did. the electric locks do not work and the horn goes off if i try to open with...


something puts bcm into safe mode. take neg. battery cable off and touch it to pos. post for 30 sec. leave unconnected for 6 hrs then reconnect. should work after that. just did mine. dealer wanted 400$ to change door switch. doing this lets the bcm reset itself

Feb 09, 2011 | 2005 Chevrolet Colorado

1 Answer

The horn is not working on my 2006 chevrolet colorado and now it seems to be little loose can I fix this myself? I am afraid of messing up the airbag


Hello. the hron is this vehicle is operated by the BCM. this really requires a scan tool to check out. to answer your question if you have acces to a scan tool, you shouls be able to check the horn system out

Jun 11, 2010 | 2006 Chevrolet Colorado

1 Answer

Where is the 02 sensor on 04 colorado


O2 SENSORS LOCATED ON THE EXHAUST MANIFOLD AND ONE EXHAUST PIPE BEFORE CATALYTIC CONVERTER.RADIO NOT SHUTTING OFF PROBLEM IN THE BCM.THE WIPERS WONT SHUT OFF.PROBLEM IN THE WIPER MOTOR OR SWITCH.IF SEAT BELT LIGHT STAYS ON YOU HAVE A ELECTRICAL PROBLEM THIS WOULD BE A DEALERSHIP FIX.

Apr 22, 2010 | 2004 Chevrolet Colorado

1 Answer

2004 colorado turnsignals


your turn signals go thru the BODY CONTROL MODULE.its located on passenger side kick plate down where you feet are.i dont think that is problem ,but its is sometimes.i am not sure where sound comes from,i assume its behind the instrument cluster.BCM is like computer in your truck.turnsignal relay is in there.

Apr 11, 2009 | 2004 Chevrolet Colorado

Not finding what you are looking for?
2004 Chevrolet Colorado Logo

Related Topics:

435 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...