Question about Cars & Trucks

1 Answer

I want replaced diesel filter from dyna lorry

I want to know the procedure to replace diesel filter from toyota dyna lorry

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Cars & Trucks Expert
  • 293 Answers

There are 2 types, one is just a cartridge just like a small oil filter, this one just unscrews like an oil filter, when you replace it there is a round knob that unscrews and becomes a pump, just pump it until it becomes firm then try starting it with your foot on accelerator until engine starts. The other has a filter with a bowl under it, they have a small bolt in the center top of the housing, undo the bolt and the filter will drop free of the housing. these have O rings top and bottom and a bleed nipple off center, loosen the bleed screw pump the pump until air stops coming out the bleed, close bleed nipple then follow the same start procedure. any fuel leaks will stop your engine from starting but do not over tighten either filter because they can be damaged

Posted on Nov 26, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: water pump replacement procedure 2005 2500 dodge with cummins diesel

take off old water pump. clean up area on the motor real good.do this by using a scrapper and cleaning slolvent. when thats all done put hi temp silicon on the block water pump and the put gasket on silicon. let dry for like five minutes. put in on torque bolts to specs.

Posted on Mar 22, 2009

messstat
  • 365 Answers

SOURCE: 92 toyota pick up what is the procedure to replace

It's called CHILTON's...check AutoZone or NAPA for books.
Good Luck
P.S. it's a VALVE cover gasket

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i do a dpf regeneration on a toyota dyna


normally most new diesel vehicles with diesel particulate filters give you a warning light when it is ready to regenerate.if you got your handbook it may explain the method, diesel vehicles that do more short distance driving need regen more often because the filter blocks with soot particles quicker. try driving on a motorway for about 30mins at high speeds and keep engine revs up using a lower gear perhaps? or you can try cleaner addative to add to the fuel.some vehicles have to go on diagnostic equipment to instigate regeneration.hope this helps

Oct 29, 2016 | Toyota Cars & Trucks

1 Answer

Having problem on my Toyota dyna dutro so5d starting and idling perfectly but not picking up revs


toyota DYNA TRUCK. NO YEAR, NO ENGINE?
WHAT SERIES? , HOW MANY TONS.?
built from 1959 to now.
gas or diesel?
is the S05d the engine? its not on the list below. why?
. what country?
you must know diffr. countries use different fueling systems,and engines right?
lots of diesels used world wide and no country stated, be the 1st and shock us ! i live in ??? country. or better where was it bought.?
and super better, what market car is this? (BODY TAGS SHOW THIS)
Even this engine was used.!
Daihatsu DG diesel
not even the engine displacement stated.
fuel filter clean?
see if you can find your engine here.

http://en.wikipedia.org/wiki/List_of_Toyota_engines

learn the true toyota name for your engine,, and get better answers
or get the FSM book and see what injection system you have
of the many. that be first.
is engine compression good?

Dec 15, 2014 | Toyota Cars & Trucks

2 Answers

I have a Leyland 245. Where is the hydraulic filter located?


lifters are above the cam and below pushrod

Dec 06, 2014 | Cars & Trucks

1 Answer

Toyota dyna ignition key


clicking noise usually means a flat battery (solenoid clicking)

Feb 14, 2014 | Toyota Cars & Trucks

1 Answer

Misfiring of toyota dyna diesel sosda45857


run fault codes to determine the causes of the faults. IF your vehicle is too early for fault codes then have the injectors replaced as the tips may be faulty.

Feb 09, 2014 | Cars & Trucks

4 Answers

NEED TIMING MARK DIAGRAM FOR so5d


toyota dyna xzu411 timing pomp diagram

Jun 05, 2012 | Toyota Dyna Cars & Trucks

3 Answers

Toyota hilux d4d 3.0 litre fuel system light reset ?


Remove the key from the ignition but keep it handy. Important: Disconnect the negative terminal of the battery for longer than 90 seconds to prevent the risk of having the airbags deploy! Replace the diesel filter (Follow the instructions that can be found in Toyota service manuals (search www). Remove the diesel filter sensor cable (the one on top of the filter assembly). Make sure the new O-rings seat properly. Close the filter assembly by turning the locking ring until it clicks. Bleed the filter assembly by pushing the little plunger thing on the top of the assembly until pumping becomes difficult. Connect the negative back onto the battery. Insert the key in the lock and turn until the dashboard warning lamps come on, but do not start the car yet. Within 3 to 60 seconds of doing this re-connect the diesel flter sensor cable. The light should be extinguished. Obviously there could be another problem causing the light to remain on (not flashing - steady on). If the light is flashing, then you have water in the system and should follow the answer supplied elsewhere by someone else to drain the water. Now start the car and enjoy clean diesel fuel driving. You should really not wait for the light to come on steady before chnaging the filter. Some fanatics believe every 10,000km is the longest you should wait, but this depends on fuel quality, low or high sulfur content, etc. Rather do it more frequently than having to buy new injectors.

Apr 10, 2012 | 2007 Toyota Hilux 2.7

1 Answer

My 54 reg corolla is losing power on some inclines of the M4 so much so that if i try to overtake a lorry at 70 mph the lorries end up having to undertake as the car loses power down to 50mph sometimes,...


Most services don't include a fuel filter. check to see if it was replaced. If not replace it. These clog up, you get sufficient pressure but not flow

Nov 27, 2010 | 2007 Toyota Corolla

1 Answer

How to reinstall the fuel injection pump on toyota 4.2 l turbo diesel(1 hd-fte)engine


Actually this is a relativly simple fix, it is located near the diesel filter {R/H of engine} and is merely removing the feed lines and plugs, replacing the gaskets and pump, you will have to prime the unit before attempting to drive, be generous with the diesel when priming, as running them dry can be costly. replace the filter while your at it and remember to fill the chamber with fresh fuel before sealing it closed. Good luck, hope it helps.

Nov 19, 2009 | 2000 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...