Question about Jeep Cherokee

1 Answer

My windshield wipers suddenly quit working.

My windshield wipers don't work.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jeep Master
  • 420 Answers

First check the fuse, if the fuse is good check to see if you are getting power at the wiper motor. Power at the motor means bad motor, no power is either the switch or wiring.

Posted on May 08, 2009

  • Scott May 09, 2009

    I thought the problem was the wipers weren't working? YOU have to do what is called trouble shooting. No one can tell you exactly what is wrong over a computer.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could be my problem for my windshield wipers to suddenly start and stop working?


It could be the screws are loose (at the bottom end of the wipers)
There may be a rubber cap you will need to access the screws. (Also worth checking if the wiper motor is working when wipers are not)

Other possibility, the wiper motor fuse is loose with intermittent connection - locate the fuse box and take out all fuses, inspect them for damage/burn marks and insert them firmly back.

Hope this helps

Sep 29, 2016 | 2003 Buick LeSabre

1 Answer

What caused windshield wipers to quit working?


Begin troubleshooting by checking for an open wiper fuse.

Feb 15, 2016 | Cars & Trucks

1 Answer

I'm driving in rain, wipers working good, all of a sudden they quit! I drive for 15 min, check again, they work for a while, then quit again...what in the problem?


If your not familiar with automotive electronics an module control of components , I suggest you take it to the dealer . They have the tools to diagnose this type problem !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper PCB relay


?€¢
Wiper high PCB relay


?€¢
Windshield wiper motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
WPR fuse 25 A


?€¢
WSW fuse 10 A


Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
High Speed Operation When the wiper switch is in the high speed position, ground is applied through the windshield wiper switch high signal circuit to the body control module (BCM) indicating the wiper high speed request. In response to this signal, the BCM then energizes the wiper PCB relay, as stated above, and the wiper high PCB relay by applying ground through the control circuit to the coil side of the relay. With the wiper high relay energized and its switch contacts closed to the high speed control circuit of the wiper motor, the motor will operate at high speed.
Wiper motor high speed operation and the wiper high speed PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
You could Have a switch problem , BCM problem ,PCB relay problem , the pcb relays are non serviceable an the whole under hood fuse box would need to be replaced . Malfunctioning motor bad ground some where etc.....

Dec 20, 2015 | 2008 Chevrolet Impala

1 Answer

Windshield wiper stopped working


arm/linkage came loose.. its at the base of the windshield..

Dec 30, 2013 | Hyundai Cars & Trucks

1 Answer

Windshield wiper doesn't work


If both wipers don't move, could be the switch or the wiper motor.

Jul 02, 2012 | 2000 Pontiac Montana

1 Answer

The motor on the sprayer for the windshield wiper solution quit working. No longer can hear it trying to pump the fluid.


Check your fuses for any blown ones. If you don't find any blown fuses to replace, you will need to replace the wiper fluid pump.

Aug 26, 2011 | 1998 Oldsmobile Eighty Eight

1 Answer

Windshield wipers get slow and then quit.


It sounds like your wiper motor is dying

Oct 08, 2009 | 2000 Lincoln Town Car

2 Answers

Windshield wipers don't work right. Try to and quit mid cycle.


YOUR WIPER MOTOR COULD HAVE BINDING LINKAGE AND PIVOTS.TRY LUBRICATE THEM WITH WD40.TRY NOT TO GET ANY ON WINDSHIELD.IF THIS DONT WORK WIPER MOTOR COULD BE FAULTY.

Sep 27, 2009 | 1996 Acura TL Series

1 Answer

The wiper quit working


it sounds like the ball socket linkage has parted as you should not be able to move the wipers with ease.

May 12, 2009 | 2002 Mercedes-Benz C-Class

2 Answers

Rear Windshield Wiper Problems


Check the wiper motor connection if its touching anything and loose it will automatically ground out and check at connection make sure you put some gel and then snap it in/ Please rate my response thank you very much

Jan 31, 2009 | 2003 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

523 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...