Question about Cars & Trucks

Open Question

Replace head gasket on 86 mercedes 190e 2.3l

I need to know how many tty bolts im going to need to buy

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

Ad
  • 4 Answers

SOURCE: torque specifications for head bolts 1995 Jetta 2.0

First pass, torque them to 30 Ft Lbs working from the center outward. Then go back again and torque them to 75 Ft Lbs.

Posted on Feb 21, 2009

chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

spanish pete
  • 18 Answers

SOURCE: dash lights om 1987 mercedes 190e out at heater controls

Remove the metal part of the ashtray, you will see two screws that hold the ashtray plastic part on, underthis is the screws for the lower panel
You can now carefully lift the whole panel away.

Posted on Mar 31, 2009

  • 15 Answers

SOURCE: replacement of cylinder head gasket freelander 1800 petrol

DEFINITELY NEW BOLTS.
1ST STAGE 20 NM
2ND STAGE 180 DEGREES
3RD STAGE 180 DEGREES.....JOB DONE.

Posted on Jul 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the head gasket on an 86 FORD BRONCO


A torque wrench to tighten the bolts to spec. Necessary tools to remove the head bolts. A gasket scraper for the rocker cover gasket and the head gasket.. If you have a blown head gasket the chances of a warped head is about 98%, so be prepared to have the head machined flat before reinstalling the head. You might want to do a valve job and replace the valve stem seals since you're going to remove the head. If you decide to do a valve job, you MUST do both heads or the engine will never run good.

Aug 12, 2016 | 1986 Ford Bronco II

1 Answer

How to replace alternator belt for 1984 Mercedes 190E.


Loosen the bolts underside of alternator and then loosen the tension arm alongside the alternator. After replacing the belt, use a piece of wood a suitable length and size to re-tension the belt whilst tightening the tension arm then tighten the lower bolts.

Jan 03, 2015 | Mercedes-Benz Mercedes Benz 190e 2.6...

1 Answer

Serpentine belt routing on 93 mercedes 190e 2.6


Go to the following link and the first photo shows the belt routing. I hope this helps as I know changing the belts on these vehicles can be a major pain in the neck.
Pelican Mercedes Benz Tech Article Mercedes Benz Drive Belt Replacement...

Dec 11, 2014 | 1993 Mercedes-Benz 190

1 Answer

Need 2010 suzuki swift 1.5 gls torque specs


OLD POST.( M15a torque settings)outside canada
we dont have any m15a here in usa,sorry
but my cousin does (in SA)
so found it.
I TRIED TO FIND A PDF FOR YOU.
using google "m15a pdf" hits.
2004 FSM real.
http://ssoc.co.uk/forums/showthread.php?1835-Workshop-Manuals

FIRST GOOGLE HIT. LINKS TO THERE
THAT LINKS TO AND IS HERE.
the book.
http://www.mediafire.com/download/cywbm9kgvii/Suzuki+Swift+Workshop+Manual.pdf

40MB PDF , LARGES
I DID ALL THIS, CUZ, ME CoUSIN FRED ASKED ME TO
FIND THIS BOOK for him,SO TOok efforts.

AND IS ANGLE SET.5ff93f1e-0722-4b3d-88c9-8e7490bd13ac.jpg24562683-pxhbyeemlouognp102sfyz1p-5-2.jpg

Jun 04, 2014 | 2005 Suzuki Swift 1.5

1 Answer

How to replace head gasket on a 1992 mercedes-benz 190e 2.6


There really are a lot of steps to go through. But its all straight forward no special tools, though you may need an assistant, and you will have to remove the timing chain and mark everything. It would be best to get a workshop manual.

Jan 26, 2011 | 1993 Mercedes-Benz 190

2 Answers

1997 cavalier head gasket replacement with a 2.2. Also need the torque specs and sequence for the head bolts


Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Nov 16, 2010 | 1997 Chevrolet Cavalier

1 Answer

Reaplaceing head gasket I need toruq specs for haed bolts. for 2002 2.4 12 v engean


the final torque setting is approx 80 foot/pounds incrementally if they are tty torque to yield bolts) Depending on the manufacturers of the replacement head bolts some require besides the obvious torque sequence followed either a TTY or a degree tightening after an initial sequence tightening while using the proper 30w , 10W-30 or manufacturers own mixture of molybelenum. Hope this helps.

Mar 06, 2010 | 2002 Toyota Camry

1 Answer

Cant get head off 86 mr2.


Head jobs take time, patience, and most importantly a book. As far as the bolts, take the allen head into the parts store and find a Torx bit that is slightly bigger and beat it into the stripped bolt head, loosen and replace the bolts with new ones. Good luck.

Apr 28, 2009 | Toyota MR2 Cars & Trucks

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Can I change engines


you would need to get all the wiring harness, computers, mounts and accsecories but it can be done -jeff please rate

Sep 01, 2008 | 1993 Mercedes-Benz 190

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...