Question about 1993 Jeep Grand Cherokee

1 Answer

93 jeep grand cherokee start then die - 1993 Jeep Grand Cherokee

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 46 Answers

Bad battery maybe?

Posted on Jul 07, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: 93 Jeep Grand Cherokee Won't start

Are you getting spark from coil wire when cranking? If so, check the cap & rotor. If not, the most common failure is the crank sensor. If you have a 4,0, you can find it on the drivers side of the bellhousing, in line with the flywheel, just where it's annoying to work on. There is a test you can make, but I don't have the specific test values or the correct terminals to check. (you can find that info in any half decent manual.
Good luck

Posted on Jan 08, 2009

polarcycle
  • 1392 Answers

SOURCE: 1993 Jeep Grand Cherokee Laredo wont drive when put into gear

No, not with out a lot of work. Electronics are most likely different on the 2 also.

Posted on Mar 11, 2009

moparownr
  • 667 Answers

SOURCE: 93 jeep 4.0 not starting

check the ignition coil pick up

Posted on Mar 23, 2009

  • 50 Answers

SOURCE: 93 Jeep Grand Cherokee Won't start

The crankshaft position sensor was seriously problematic in those old jeeps. It's located towards the top of the bell housing slightly to the driver's side I think.

Posted on Apr 15, 2009

  • 218 Answers

SOURCE: 1995 JEEP GRAND CHEROKEE RAN AND DIED WILL NOT START

IS IT THE 4.0L?IF SO U MAY HAVE A BAD CRANKSHAFT POSITION SENSOR.

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep starts but immediately dies off


run fault codes and check for MAF/MAP and VAF sensor problems

Feb 22, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

My 93 jeep grand cherokee is not getting fuel...if I disconnect the negative post for awhile and then reconnect it, the jeep gets fuel and will run....what is going on?


If the check engine light does not light up on the dash when you turn on the ignition, at those times when your jeep doesn't want to start, then your main jeep ecm is in need of repair. The fuel pump relay will get energized only after that check engine light comes on. It's a known problem, especially with the first and second year production Grand Cherokees, 93 and 94.

Jun 30, 2012 | 1993 Jeep Grand Cherokee

1 Answer

I have a '93 jeep grand cherokee limited 5.2 v8.


Disconnecting your battery, as you must've done when changing the starter, will cause the ecu to revert to factory settings and the computer will have to relearn the proper idle for your jeep.

Mar 30, 2012 | 1993 Jeep Grand Cherokee

1 Answer

I have a 93 jeep grand cherokee with no power at all still idles fine but has no go like im trying to pull a house also in park the higher you rev it the more it starts to sputter and want to die any ideas...


hi; no power ? 93 jeep grand cherokee 4x4; cat. was burned out ! badly hot !. i did cut it off, ! put back with out a cat....just a new muffler, shot tail pipe..
put in new spark plugs,, new dist. rotor, ? those's, old plugs were very black!

but, rough starting, how, do you find the power codes, ? or reset, the computor ?. just has no power !??. what's wrong ?. can, i reset ?..can i buy some fuel treatment?????

Dec 21, 2011 | 1993 Jeep Grand Cherokee

1 Answer

How do i remove the security , my jeep will not start


Jeep Grand Cherokee since '93 at '98 are covers under ZJ sub-model; I have the first generation '93 5.2L V8 and this information -->> Alarm_96_Jeep_Cherokee (pdf)

Work for me.

Hope this helps.

Nov 25, 2010 | 1995 Jeep Grand Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

1 Answer

93 Jeep Grand Cherokee Won't start


The crankshaft position sensor was seriously problematic in those old jeeps. It's located towards the top of the bell housing slightly to the driver's side I think.

Apr 15, 2009 | 1994 Jeep Grand Cherokee

1 Answer

93 jeep 4.0 not starting


check the ignition coil pick up

Mar 23, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...