Question about 2008 Chrysler Town & Country

Open Question

Arm rear turn wiper

Needs to be replaced

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Why is my rear wiper arm pointing toward the ground and won't stay up on the glass? My child decided to use the rear wiper arm as a monkey bar and pulled it all the way down, so it points straight to

It could be that the wiper arm need replacing as there are serrations on the motor shaft and these hold the arm in place so try a new arm .

Feb 07, 2015 | Cars & Trucks

1 Answer

How do you replace the rear wiper on a 2009 Scion XD?

You can make use of following procedure to replace rear wiper in ur scion xd.
Pull the rear wiper arm away from the rear window in order to access the wiper blade.

  • Locate the hinge where the blade mechanism meets the wiper arm and squeeze the plastic tabs on the blade in order to release it from its locked position on the arm. In some cases, instead of tabs, there is a small button that must be pressed to release the wiper from the arm.
  • Detach the blade from the arm and slide the old blade out. Insert the new blade into the wiper arm and lock the blade in place.
  • Return the wiper arm to its set position. Before driving, wet the window and test the wiper to make sure it is operating properly.
  • Dec 14, 2010 | 2009 Scion xD

    1 Answer

    Replace the rear wiper arm shaft

    There is a plastic cover that pops off at the pivot end of the wiper arm. pulling up on this with a hook of some kind from the furthest end should release it. Under it you will find a nut that holds the wiper arm to the shaft. It's quite common for the nut to come loose and the shaft spins without moving the arm. Try tightening this nut (with the ignition on, be sure the wiper motor is off, then turn off ignition and put the wiper arm in the parked position). This is a common problem if you've ever tried to turn on the wiper when it was frozen to the glass.

    Feb 26, 2010 | 2000 Honda Odyssey

    3 Answers

    How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?

    Front Wiper Motor
    Removal & Installation

    NOTE A new wiper motor assembly comes with the linkage arm installed.
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Remove the windshield wiper mounting arm and pivot shaft
      WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
      NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
    3. Remove the 3 bolts and the wiper motor.


      Fig. Wiper motor and linkage

    To install:
    1. Install wiper motor and bolts.
    2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
    3. Install windshield wiper mounting arm and pivot shaft.
    4. Check wiper operation.

    Rear Wiper Motor
    - Removal & Installation
    1. Remove the rear pivot arm.
    2. Remove the rear wiper motor shaft nut cover
    3. Remove the rear wiper motor shaft nut.
    4. Open the lift gate window.
    5. Remove the rear wiper motor cover trim panel.
    6. Disconnect the electrical connector.
    7. Remove the 2 rear window wiper motor nuts
    8. Remove the rear window wiper motor.

      Fig. Rear wiper motor view-2008 model shown, other years similar

    To install:
    1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
    2. Reconnect the electrical connector.
    3. Install wiper motor cover trim panel.
    4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
    5. Install shaft nut cover.
    6. Check wiper operation.

    Good luck (remember rated this post).

    Feb 25, 2010 | 2004 Ford Escape

    1 Answer

    Can't remove rear wiper to replace on 96 caravan

    Lift wiper arm from rear window. then release latch that holds the blade to the wiper arm.( It's small tab)

    Jan 16, 2010 | 1996 Dodge Caravan

    1 Answer

    How to replace the wiper insert at the back of

      1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
      2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

      1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
      1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
    b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
    c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

    Sep 12, 2009 | 2005 Toyota Matrix

    1 Answer

    My 07 nissan murano rear windshield wiper doesn't work properly it goes the wrong way, not on the window.

    You need to adjust the wiper arm location. Loosen the 12 mm or 10 mm nut that holds the rear wiper arm. Wiggle the arm until it comes off. Then turn on the rear wiper for a second and turn it off, leaving the key on. This way the rear wiper motor will do it's sweep, and them park where it's suppose to. Then reattach the rear wiper arm and secure the nut and recheck.

    Thanks Jay!

    Jul 20, 2009 | 2007 Nissan Murano SE

    2 Answers

    Rear wiper blades

    No...blade comes off end of arm... If in doubt, most "supermarket" style parts outlets will put it on for free.

    Feb 09, 2009 | 1997 Toyota 4Runner

    1 Answer


    Remove the rear pivot arm.
    Lift the pivot arm to the upright position.
    Slide the locking tab out.
    Pull up and remove the pivot arm.
    Remove the rear wiper motor shaft nut cover.
    Remove the rear wiper motor shaft nut.
    Remove the rear wiper motor cover.
    Remove the rear wiper motor bracket nut.
    Remove the bolt and the rear wiper motor.

    Jan 29, 2009 | 2005 Ford Escape

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    49 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts


    Level 3 Expert

    77186 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers


    Level 3 Expert

    814 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides