Question about 2008 Chevrolet Impala

1 Answer

Right rear turn signal and brake light does not

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 171 Answers

Go to the local auto parts store and tell them you need a new bulb for your right rear turn/brake light. It should be easy to install by going into the trunk. A good parts store will install it for you at no charge.

Posted on Nov 26, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Chev Cavalier 2003 only one rear turn/brake/hazard light

I have a 2002 Chev Cavalier that had the same exact problem. I replaced the bulb harness (purchased from a chevy dealership for around $5) which was fairly easy to do. I have had zero problems with it since.

Posted on Dec 03, 2008

  • 88 Answers

SOURCE: rear brake lights don't work

you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

Posted on May 23, 2009

  • 1986 Answers

SOURCE: 1994 chevrolet pickup - brake light problems

There will be an electronic flasher module located under your dash near the steering column (don't know it's exactly location as it varies). It sounds like this unit may be faulty.

Posted on Aug 21, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

  • 1 Answer

SOURCE: turn signals going crazy when I push on the brakes

OK, after more than a year of living with this problem, and replacing the turn signal switch (which did _not_ fix the problem), and checking every bulb and every fuse multiple times, I finally broke down and turned my mechanic loose on this problem. He knew right away that it was a grounding issue. He didn't know where, but he hooked up an aux ground to the negative post on the battery and the problem went away. That diagnosed it, the solution turned out to be more difficult as he had to disconnect most of the ground wires connected to the chassis, and wire brush all the spots and then reconnect them all before he finally figured out which it was that was causing the problem. I told him I'd take all those apart again and grease them and then put them back together so they're more permanently fixed. He had seen this issue before, multiple times on GM vehicles. Now I know about it too, and I'm sharing it to hopefully save somebody else some grief.

Posted on Nov 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Left bleaker and break light not working. Turn signal works bleaks faster than right side.


Has the vehicle been in an accident on the left rear side. First check the bulb to be sure it is not defective, trade it out with the side that works properly to test. If the bulb works well then My thought are you may have a shorted wire. The turn signal flasher works by heat build up within the flasher the heat is caused by the load of the bulbs, the load heats the metal spring causing it to open the circuit then as quickly as it cools down the circuit closes again lighting the bulbs.
There is also a possibility of a defect in the turn signal mechanism on the steering column. The turn signal switch on many models does three different things on many models that use the same bulb element / or bulb for brake and turn on rear of vehicle. It controls the circuit for brake light by sending power both left and right side rear when turn signal is in neutral position then when turn signal is in left turn the switch cancels brake light power to left side rear and supplies flasher power to left side while maintaining brake light supply to the right side rear, and so on opposite when the right turn is chosen on turn signal switch. The turn signal indicators on the dash normally run off the same circuit as front turn signal bulb only which is also controlled by turn signal switch. Front has turn signals but no brake light.
I think there is an additional load on the left side rear turn circuit and it could be either a wire that is shorted or the turn signal switch if the same bulb element is used for both functions.
Often times if trailer lighting is connected the flasher will also blink a little faster because of the extra load of additional bulbs.

Feb 15, 2015 | Cars & Trucks

1 Answer

If it is the blinker switch why do I not have brake light on right rear side as well as no turn signal


The brake light circuit runs through the blinker switch, which is how the turn signal is able to override the brake light.

Jan 13, 2015 | Seat Cars & Trucks

1 Answer

Brake light and turn signals


check to see if the wire connector is plugged in properly

May 30, 2013 | 2003 Jeep Liberty

1 Answer

1998 chevy lumina: rear window brake light not working, left brake light not working, rear left turn signal not working


See if bulbs have burnt out in the left brake light and rear turn signal (one bulb if combined) and also rear center high mount brake light.

If the left turn signal has a slower speed than the right turn signal, this is a symptom of a bulb or bulbs burnt out.

Usually, the wiring is not a problem, but I would not rule wiring (or sockets) as a problem out.

Good luck on this repair.

Jan 19, 2011 | 1998 Chevrolet Lumina

1 Answer

REAR BRAKE LIGHTS DO NOT COME ONLY TAP LIGHT IS


Check for power at the turn signal switch. White wire comes from brake switch switch into the turn signal switch. The brake light switch is working because the high mount brake light is working..right? Do the turn signals work ok? if so, then the wiring is OK. The brake signal wires that come out of the turn signal switch are dark green(right) and yellow (left).

Oct 27, 2009 | 2001 GMC Safari

4 Answers

Brake light, Turn signal not working rear right 06' Focus


I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Jul 26, 2009 | 2000 Ford Focus

2 Answers

2001 Explorer Sport ,Rear Driver Brake Light and Turn Sig. Broke


Rear lights are double filament bulbs one side for the lights other side for the brake/turn signals so it still may be a bulb. Do u have a test light or volt meter you can check to make sure u have power there when brakes or turn signals are activated. Or just try another bulb.

Feb 12, 2009 | 2001 Ford Explorer Sport

Not finding what you are looking for?
2008 Chevrolet Impala Logo

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...