Question about 2006 Ford Fusion

Open Question

Where is the body control module on a 2006 ford fusion

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
rockitman187
  • 2559 Answers

SOURCE: No radio volume (locked after changing battery of 06 Ford Fusion

Has to be unlocked by a dealer.

Posted on Jan 07, 2009

Ad
  • 12173 Answers

SOURCE: Failed emissions What fuse for OBD port on 2006 Ford Fusion?

check the out put from the computer to the obd ll port if good need to check the wiring harness ,connections and pin contacts from computer to obd ll port connections possible short,frayed or broken wire

Posted on Feb 14, 2010

  • 5520 Answers

SOURCE: 2006 Ford Fusion SEL - TPS

The TPS is an easy part to replace. It has 2 screws and 1 electric connector. It is about the size of a butane lighter and attaches to the metal airhorn.

There is only a slight adjustment possible for this part. One end has an elongnated slot for the screw. Just look at where the old part was adjusted and replace it that way. The only thing you need to watch is aligning the slot on the throttle shaft with the indentation on the TPS.

While you are replacing the part, disconnect the battery on the POS cable and this will reset the "check engine" light on the dash. Then reconnect and drive your car.

Posted on Apr 30, 2010

  • 5 Answers

SOURCE: 2006 Ford Fusion. Left front door inside handle

This link is from the handle to the latch. The door panel has to be removed in order for this problem to be fixed. The linkage is inside the door panel, it is a small diamater metal rod called a link. If you do the job yourself be careful not to break the door panel. In a shop, the labor is 1 hour for the job & if any, parts will be a seperate charge.

Posted on May 08, 2010

toneman2121
  • 775 Answers

SOURCE: removing alternator on a 2006 ford fusion v6

the alternator probably is accessable from the underside of the car without removing the compressor, which would require extensive knowledge and expensive equipment. the best thing to do is purchase a repair manual. this inexpensive investment has detailed procedure and pictures to help you tackle this repair.

Posted on May 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know what code 2110 ford fusion 2006 se


P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection help.png Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more: http://helpforcars.net/obd_codes/p2110_2006_ford_fusion.html#ixzz3mV0SayWu

Sep 22, 2015 | 2006 Ford Fusion

1 Answer

What does 2110 code on 2006 ford fusion mean


P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection > Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more: http://helpforcars.net/obd_codes/p2110_2006_ford_fusion.html#ixzz3mUz73ACP

Sep 22, 2015 | 2006 Ford Fusion

1 Answer

How do you replace ETC on 2006 Ford Fusion


( Electronic throttle control ) Is this what your talking about ? What part do you want to replace , the throttle body , the APP - accelerator pedal position sensor. the control module ? Is the etc light lit on the dash ? You Need to have it checked out ,codes an go from there !

Sep 22, 2015 | Ford Cars & Trucks

2 Answers

How can I reprogram bcm on 2006 ford fusion


You need a factory scan tool , it only costs about $3,000 ! Does the back lighting work every where else , Instrument cluster , switch on steering wheel, door switch's etc.. If so you have another problem , because all the back lighting is controlled by the SJB - smart junction box , that's what ford calls there body control module !

Feb 26, 2015 | 2006 Ford Fusion

1 Answer

2006 ford fusion, steering wheel has horn, cruse control that doesn't work, is their a fuse


I would think the clock spring is bad ,the clock spring is ribbon wire wound in side a plastic body inside top of steering column. The steering wheel has to be removed to get at it. It is used so you can turn the steering with out losing power for the horn and cruise control. How cars clock spring works

Jan 19, 2015 | 2006 Ford Fusion

1 Answer

What is a bcm


body control module. controls lighting, and communicates with other modules.

May 29, 2014 | 2013 Ford Ford Fusion Hybrid

1 Answer

My dome light on my 2006 Ford fusion stays on for 11 mins straight how can I fix it


Hi.. On your Fusion the dome light will stay on
If the Body cumputer detect any door open,
This happen when the Door Ajar Switch when bad.
The Body computer Don't receive the signal of the switch.
After 11 Minutes The Body will turn off the Light .
With a system Called Battery Saver.
The Alarm system will not work right.
I recomend Try to do Computer Diagnostic.
To find wich Ajar switch is bad and have replace it
I hope this help on your question.

Thank you for use Fixya. Feel fre to ask anything..

May 17, 2012 | 2006 Ford Fusion

1 Answer

2006 ford fusion code p 0755


You have a electrical problem , not the transmission !
P0755 Ford Shift Solenoid 2 Circuit Malfunction

CIRCUIT MALFUNCTION . Could be the driver (transistor) in the control module that turns the shift solenoid on > Videos on youtube testing control module driver .

May 07, 2017 | 2006 Ford Fusion

1 Answer

Is it hard to replace the mass airflow sensor in a 2006 ford fusion?


this is not a difficult fix the mass air flow sensor is in line between the air filter and the throttle body just loosen the hose clamps and pul it out.

Oct 17, 2010 | 2006 Ford Fusion

2 Answers

My check engine light has come on for my 2006 Ford Fusion and 3 codes came up...P0010, P2104, and P2112. Any ideas what these mean?


Fuel and Air Metering and Auxiliary Emission Controls P2104 Throttle Actuator Control System - Forced Idle
P2112 Throttle Actuator Control System - Stuck Closed
If it's not the pedal, it has to be throttle body, senor or harness related.

Jan 16, 2009 | 2006 Ford Fusion

Not finding what you are looking for?

Open Questions:

See all 2006 Ford Fusion Questions

2006 Ford Fusion Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...