Question about Hyundai Cars & Trucks

1 Answer

How do i replace the sump on a hyundai accent

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 35 Answers

Remove Exhaust pipe, remove all bolts around the sump. (10mm size).
Sump will still stick, because there is no gasket. Its like glued on with silastic, which is acting as gasket. Get a flat screwdriver in the gap between block and sump and leaver it carefully away. Do not bend the sump too much, use a knife to cut the silastc piece by piece. Clean the surfaces well and put new silastic on to refit.

Posted on Dec 02, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 31 Answers

SOURCE: 2005 Hyundai accent overheating, radiator

A car can overheat for a lot of reasons.First make sure this is the problem by checking the radiator hose or water level. Open the radiator cap when the car is cold, crank it, and then watch the water level. If it drops when the car warms up this is not the problem.
The tools you will need will depend on what you have to take off to get to it. If you can access the thermostat you should only need a ratchet or wrench to remove it and something to scrape off old gasket with.
Location:The thermostat should be inside the thermostat housing on the motor. Follow your top radiator hose to the place where it goes into the motor. There should be a sort of dome shaped housing there with probably a bolt on either side of it.The thermostat is inside that.
This is a reasonably easy job, but shouldn't be done carelessly. It's also kind of messy.
When the car is cold remove the bolts from the housing with a ratchet. Lots of coolant and water will drain out. But the thermostat will be visible.Pay attention to which side of the thermostat is up.It should just lift up. Remove all the old gasket from around the area and clean it up well. Replace the thermostat and gasket then the bolts. Be very careful not to over tighten the bolts or the housing will be ruined.

Posted on Apr 22, 2009

fastboyz
  • 674 Answers

SOURCE: 2002 Hyundai Accent Problem

first thing i need to know is did the timing belt break?
second is are you sure you aligned the timing marks and after the belt tensioner was tight you rechecked to make sure the timing stayed where you had it.
next step would be a compression check to if a valve was bent whenchanging the belt
i have seen this happen and this engine is an interferance engine.
later paul

Posted on Sep 28, 2008

  • 297 Answers

SOURCE: How to replace a window cable on hyundai accent

I use to have a Hyundai Pony once, there was no cable there.
But still you need to remove the inside cover etc. to get there.
I became an expert blindfolded and a hyunday hater afterwards.

Posted on Apr 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cam sensor 2002 hyundia accent 1.5?


    More images for Where is the cam sensor 2002 hyundai accent 1.5

    Hyundai Crankshaft Position Sensor Removal - YouTube

    ? 3:42
    https://www.youtube.com/watch?v=0YLYDU_5w8w
    Jul 12, 2012 - Uploaded by richpin06a
    Hyundai Elantra Crankshaft Position Sensor Removal.

    Hyundai accent 2001 - YouTube

    ? 2:44
    https://www.youtube.com/watch?v=fzqMNho3xIU
    Nov 25, 2012 - Uploaded by mig dups
    2000 Hyundai Accent GS turns over - no start. ... HyundaiCrankshaft Position Sensor Replace Timing Belt ...


Dec 26, 2015 | Cars & Trucks

1 Answer

How do I arrange my spark plug wires on my Hyundai Getz go 2002


How to change spark plugs hyundai accent 01 - 05 - YouTube

? 3:18
https://www.youtube.com/watch?v=tU2vwisJ7v4
Feb 16, 2012 - Uploaded by PNBNC
I filmed this right after changing my old plugs, I figured it was easy enough to film and some people can profit from it. for a ... Coil, you mean wire lol ... When you go to put the spark plug back in, never start it with the ratchet.

How To Replace Change Install Spark Plugs 2001-06 ...

? 3:17
https://www.youtube.com/watch?v=yVV2KcPDFIo
May 14, 2013 - Uploaded by 1A Auto Parts
... spark plugs. This video is applicable to the 2001, 2002, 2... ...spark plugs. This video is applicable to the 2001, 2002, 2003, 2004, 2005, 2006 Hyundai Elantra 2.0L. ... +queentonks A little know-how can go a long way. We're glad ... When do you think is good to replace my spark plugs wires? My spark ...
2001 Hyundai Accent Firing Order: Engine Mechanical ...www.2carpros.com/.../hyundai-accent-2001-hyundai-accent-firing-orderApr 23, 2009 - Engine Mechanical problem 2001 Hyundai Accent 4 cyl Two Wheel Drive Manual 95000 ... Now I'm trying to figure out how they go back on. How do I find out the Engine Firing Order for my car - Hyundai Accent 2001 1.5L?Which is cylinder 1 - 1.6 Accent - Hyundai Forum: Hyundai ...www.hyundaiperformance.com/.../16837-cylinder-1-1-6-accent.htmlJan 13, 2003 - 3 posts - ‎3 authorsFrom what I read though, the coil pack is configured as 1 4 2 3. I'm assuming the first wire on the coil pack goes to cylinder 1. Can anyone ...

Dec 16, 2015 | Hyundai Cars & Trucks

1 Answer

How do I change spark plugs on a Hyndai Accent 2009?


Hyundai Accent How to replace spark plugs - YouTube

? 3:21
www.youtube.com/watch?v=TQSplCznN9c
Jan 15, 2014 - Uploaded by Dima Travnev Hyundai Accent How to replace spark plugs ... Part 1 2009 Hyundai Accent tune up Spark plug replacement in 720pHD - Duration: 14:00. by ...

Sep 09, 2015 | Cars & Trucks

1 Answer

Where is the location of the crankshaft position sensor of a hyundai accent,2006


When you stand infront of the car. open the bonnet, look where the engine and gearbox join. left of the gearbox and engine joint. below the head and above the sump. a black sensor with one 10m bolt. one black wire about 4mm thick which plug into a wire coming from the top of the engine. see picture 6687b655-d24c-4387-bbee-71c277e9bec5.gif

Aug 18, 2014 | 2006 Hyundai Accent

1 Answer

Lub oil dip stick level drop to half in a day.


check for a serious leak like at the oil filter , sump plug loose , rear main seals and crankshaft pullet seal and pcv valve not working correctly. Check for leaks at rocker cover gaskets.

Dec 28, 2013 | 2000 Hyundai Accent

1 Answer

2004 Hyundai Accent would not start after it had warmed up. Subsequently it would not start at all but the valve cover blew off.


That sounds like a timing/ cooling system issue. The coolant sensor would adjust the timing etc. Your tech would have to scan the car & check the live readings (HOT & COLD) & check the emissions. Put all the pieces together & solve the puzzle

Mar 11, 2017 | Hyundai Motor 2004 Accent

1 Answer

WHAT TO LOOK FOR IF THE IS ENGINE LEAK


I'm presuming an oil leak?

Check around the sump where it bolts to the bottom end. Visually inspect the sump for holes (altho you would be losing oil pretty severly if there is). Check around the oil filter, might not be sealed right.

One way to narrow the leak location is get a sheet of card and put it on the ground under the engine bay overnight. It should show you where the oil is dripping from or what its dripping off.

Also Accents have a habbit of dropping oil level very quickly when they are getting close to requiring an oil top up.

Dec 05, 2012 | 1999 Hyundai Accent

2 Answers

2000 hyundai accent passenger door willnot


the door 'lock/unlock' actuator is siezed up (corroded).... replace it (or have it replaced).

Oct 03, 2009 | 2000 Hyundai Accent

2 Answers

How do I replace headlamp bulb?


Some imports require the entire light assembly to be removed in order to replace headlamps. Look to see if there are angled rods on the back side of the light assembly. If so, see if the can be pulled straight up towards the hood of the car. When they are released the headlight will be able to come forward. Good luck. Hope this helps.

Apr 25, 2009 | Hyundai Motor 2004 Accent

1 Answer

How to replace a window cable on hyundai accent


I use to have a Hyundai Pony once, there was no cable there.
But still you need to remove the inside cover etc. to get there.
I became an expert blindfolded and a hyunday hater afterwards.

Apr 14, 2009 | Hyundai Motor 1998 Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...