Question about 1999 Jeep Grand Cherokee Limited
It's a 4.7 L , trying to find a diagram or reference so I can find the IAT sensor.
Great question, on some cars, its NOT THERE.
nice how you actually state engine option.
but way not post symtoms, or evidence. (got DTC errors from scan tool?)
The Intake Manifold Air Temperature IAT sensor is located on the left side of the intake manifold.
For a temperature of 68F (20C) the resistance is approximately 6000 ohms. For a temperature of 104F (40C) the resistance is approximately 3300 ohms. (this forum hates degrees symbols , dang)
its just a Thermistor. NTC
on some cars, its in the MAF
others its screwed in to the air cleaner box.
others, (yours) its in the air plenum. (MAP base EFI)
the map system needs the plenum baro and temp. TOGETHER.
Posted on Nov 26, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
P0700 means there is a transmission fault code in the transmission controller. Since the transmission controller doesn't have a light attached, it tells the engine controller to turn the light on using this code. You'll have to access the transmission controller to further diagnose the problem.
Posted on Jun 14, 2009
There are two parts to it, a voltage resistor, and the EL panel itself.
You need to remove the console first. There are 2 screws under the front rubber pad, two under the cup holder, two in the bin. Remove those six first, take the storage bin out, then slide the rear cupholder out, remove the two screws under the cup holder, and one in front of it.
There are a total of 6 flat screws, and 3 self tapping screws you have removed.
Put the parking brake on, shift the tranny to N, and the transfer case to the middle position if equipped.
Remove the entire console. Slide the shifter beezel as far up vertically as you can. There are 4 clips you ned to remove to do it.
You will see a blue and black wire running into the back. Follow those wires to the resistor. You will see a transparent EL panel attatched to the resistor by two clips.
Usually, one or both of these clips has come loose, causing the light to work intermittantly. Clip them back on, and turn on the headlights to confirm that the light works correctly now.
Re-install everything in the opposite order.
Posted on Oct 11, 2009
it is located right at the tail shaft of the transfer case where the rear drive shaft comes out.its the only sensor in that area.
Posted on Jan 19, 2010
Tips for a great answer:
Feb 18, 2017 | 1999 Jeep Grand Cherokee Limited
Aug 09, 2016 | 2000 Jeep Grand Cherokee Limited
Feb 05, 2013 | 1999 Jeep Grand Cherokee
Jul 06, 2012 | 1999 Jeep Grand Cherokee
Nov 26, 2010 | 1997 Jeep Grand Cherokee
Oct 22, 2010 | Jeep Cherokee Cars & Trucks
Dec 01, 2009 | 1998 Jeep Grand Cherokee
Oct 23, 2009 | 1997 Jeep Grand Cherokee
May 26, 2009 | 2004 Jeep Grand Cherokee
Jan 17, 2009 | 1999 Jeep Grand Cherokee
Feb 09, 2013 | 1999 Jeep Grand Cherokee Limited
Apr 30, 2017 | 1999 Jeep Grand Cherokee Limited
131 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: