Question about Volkswagen Cars & Trucks

Open Question

16825 and 16804

Fault codes on vw jetta 2003

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

j_del
  • 1586 Answers

SOURCE: jetta 2003 2l fault code p2182

P2181 Cooling system performance

Check Thermostat operation & Temp sensor for ECU. CHECK ENGINE CCOLANT TEMP SENSOR IN WATERHOSE, NORMALY A 4 PIN PLUG. ON SENSOR SELF PIN 1&3 OR C&D AT 0 degrees
5000-6500 ohms,60 degrees 530-675 ohms,90 degrees
200-275 degrees

Could also be the cooling fans - I've heard of fixing it by replacing the fan motor and clearing the code as well. The easy fix seems to be the coolant sensor though - I've seen several online threads where owners cleared this code by changing that sensor.

Posted on Aug 07, 2008

  • 1 Answer

SOURCE: checking the fault codes

Yes.  Next to the ash tray there is a black slide off plate that reveals the OBD I plug.  {1996 and newer can be read with an OBD II reader (read for free at Advance auto or Auto Zone)}  Once you reveal this plug on the 1995, you can plug in a single jumper wire (or even a paper clip) in the #4 and #15 pin hole.  There are two rows of pin holes, count from the upper right to the #4, then on to #15 (which will be the second to last pin hole).  Turn the ignition switch on (motor not running), insert the jumper wire for about 3 to 5 seconds, then remove the wire.  The ENGINE LIGHT will flash a hold, then the code, which will go something like this, flash, flash, PAUSE, flash, flash, PAUSE, flash, PAUSE, flash, flash, flash, flash.  Then it will repeat the codes if you just sit there and observe it.  The code in my example would be a 2214 code.
Below are some code I found on a website.  I hope this helps.  Now I ask that you take the time to answer someone elses question.  Lets all share.  Good luck, "Peace through power and knowledge"

CODE FAULT
0000 End of fault sequence
1111 Bad ground to Electronic Control Unit (ECU) or ECU failure-check grounds or replace
ECU
1119 Transmission Range - Defective wiring. Check for break or short.
1213 Vehicle Speed Sensor (VSS) - Check transmission speed sender wiring and the wiring of
the instrument cluster
1231 Vehicle Speed Sensor (VSS) (G54) - Check transmission speed sender wiring and the
wiring of the instrument cluster
1232 Throttle Position Actuator - Check defective actuator or wiring for break or short.
2111 Engine speed sender. (RPM)
2112 Ignition reference sender
2113 Hall sender - No speed signal from distributor; check Hall sensor and circuits or the
Air-flow sensor plate is not moving freely; adjust potentiometer or lever.
2114 Hall sender not on reference point or distributor out of position.
2121 Idle switch - check switch & circuit.
2122 Hall sender - Check wiring for break or short.
2123 Full throttle switch; check switch & circuit.
2132 Electronic Control Module (ECM) - No ignition to injection signal.
2141 Knock sensor 1 control at maximum ****** - test compression, change octane, adjust
timing, check knock-sensor wires.
2142 Knock sensor 1 signal - Test sensor, check wiring for break or short.
2143 Knock sensor 2 control at maximum ****** - test compression, change octane, adjust
timing, check knock-sensor wires.
2144 Knock sensor 2 signal; test sensor.
2212 Throttle Potentiometer - Value out of range.
2214 RPM Signal - Idle speed to high or engine over-revved
2221 Vacuum Control - No vacuum to control unit. Check for leaks.
2222 Manifold Vacuum - Check vacuum line and wastegate for leaks.
Pressure sensor - Sensor defective
2223 Altitude Sensor - Check sensor, check wiring for break or short.
2224 Turbo/Manifold pressure - Check turbo control wiring, check for over boost, air leak,
defective wastegate valve, vacuum leak or defective pressure sensor.
2231 Idle-speed stabilizer adjustment limits exceeded; too-fast idle. Adjust throttle for full
closing, check for vacuum leak, check ignition timing.
Or
Air Mass Sensor - Check sensor and wiring.
2232 Air mass/flow sensor - No signal. Check wiring for break or short.
2233 Air mass/flow sensor reference voltage open or short circuit
2234 ECM Supply voltage low.
2242 CO-potentiometer voltage low
2312 Coolant temperature sensor - Check wiring, check resistance.
2314 Transmission to Engine control module circuit. - Check wires for breaks or shorts.
2322 Intake Air Temperature Sensor - Check sensor and wiring.
2323 Mass Airflow Sensor - Check sensor and wiring for breaks.
2324 Mass Airflow Sensor - Check sensor and wiring for breaks or shorts to B+ or ground or
check for air leak.
2331 Oxygen Sensor Control - Out of range. - Check ignition, air intake for leaks and injectors.
2332 Oxygen Sensor - Bank 2 - Check wiring for breaks or shorts.
2341 Oxygen sensor (O2) at control limit; check CO, lambda-sensor wire, lambda-sensor
control, start valve, evaporative system and check for vacuum leaks.
2342 Oxygen Sensor Control - no signal - Check wiring, sensor.
2343 Rich limit; the pressure regulator has exceeded +10 mA for more than 5 minutes,
closed-loop; check for vacuum leaks.
2344 Lean limit; the pressure actuator has exceeded -5mA for more than 5 minutes, closed
loop; check idle.
2411 EGR System Malfunction
2412 Intake Air Temperature Sensor - Check sensor and wiring for breaks or shorts
2413 Mixture Control - Running rich
Fuel pressure too low
3424 Malfunction Indicator Lamp (MIL) failure - Check lamp and wiring.
4311 Secondary Air Injection Pump Relay - Check relay and wiring.
4312 EGR Frequency Valve
4313 Secondary Air Injection Solenoid Valve - Check valve and wiring.
4331 EVAP Carbon Canister Solenoid Purge Valve 2
4332 Ignition Circuit Final Stage - Check for break or short to ground or B+ or bad ECM.
4343 EVAP Carbon Canister Solenoid Purge Valve 1
4411 Fuel Injector Cylinder 1 or 1 & 5
4412 Fuel Injector Cylinder 2 or 2 & 7
4413 Fuel Injector Cylinder 3 or 3 & 6
4414 Fuel Injector Cylinder 4 or 4 & 8
4421 Fuel Injector Cylinder 5
4422 Fuel Injector Cylinder 6
4423 Fuel Injector Cylinder 7
4424 Fuel Injector Cylinder 8
4431 Idle Air Control Valve / Idle Stabilizer - Check valve and wiring.
4433 Fuel Pump Relay
4442 Wastegate - Defective frequency valve or wiring.
Boost pressure circuit - Check for short.
4443 EVAP Canister purge valve.
4444 No fault in system.

Posted on Oct 19, 2008

  • 1 Answer

SOURCE: transmission fluid check on a vw jetta tdi

Never ever bring a jetta to a volkwagen dealer. They will bend you over and rape you.

All you have to do is remove the top plug with a hex wrench.

Posted on Jan 12, 2009

localwonder
  • 6784 Answers

SOURCE: clicking noise inside dash board 2003 vw jetta

the relay is going bad. its freezing up. this will sometimes happen when it gets stuck in the on position.

Posted on Feb 14, 2009

emissionwiz
  • 75005 Answers

SOURCE: VW Jetta ESP issue

unless there is a ESP button (some cars have this feature, yours does not) no u can't turn it off. Have the system scanned by the dealer for trouble codes to help isolate the problem

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Radio code for my 2003 vw jetta premium 6 radio


If it is not in the owners manual you will likely need to provide the vehicle vin # and registration to a VW dealer Parts Department and they can call it in to the manufacturer and get it for you.

Apr 10, 2017 | 2003 Volkswagen Jetta TDI

1 Answer

2003 VW jetta 1.8t Open circuit emission problen


you could try a fuel addative to clean away any deposits that may be clogging the sensors, check the air/vacuum lines to and from engine , if nothing found get the OBD code number this will tell you which sensor is at fault keep me posted if you wish

Jun 07, 2014 | Cars & Trucks

1 Answer

1995 VW Jetta fault codes will not read


Hi Gregory, take the vehicle for a diagnostic scan. I am not very sure what question you're asking. I believe that you may be reporting that code 4 and 15 are reporting faults. If there are no fault codes the scanner will report 'No fault code" If it shows the two you report, a fault has occurred in those two areas. Regards John

Jul 01, 2012 | 1995 Volkswagen Jetta

1 Answer

My vw transporter t4 keeps turning off when I come to a stop then I start it and it's all good


You need to have the electronic engine control computer scanned for fault codes. This is the very 1st thing that must be done when a problem occurs like this one.

Feb 20, 2012 | 2003 Volkswagen Volkswagen Jetta

1 Answer

How do I reset the check engine light on a 1997 VW Jetta


either you will need a diag machine to plug in and clear the fault code providing the fault has been rectified if not it will not clear as the ecu will still see the fault if the fault has been repaired disconecting the battey for ten min may work or the light should go out over time vw specifiy 200 cycles of the ignition with out the fault re-occouring

May 03, 2010 | 1997 Volkswagen Jetta

1 Answer

2003 vw jetta gl 2.0 have codes p0351,p0352 and p0353


p0351- ignition coil A primary or secondary fault
p0352- ,, ,,,,,, ,,,,, B ,,,,, ,,,,,,, ,,,,,,,,,,,,, ,,,,,
p0353 - ,,,,,,,,,,,,, C,,,,,,,,,,,,,, ,,,, .,,,,,,,,,,,,,,,,
you may have a problem with yuor ingnition system

Sep 30, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

Change my 2003 VW jetta battery


a lot of the vw cars don't have coded radios but in the case that you do loose it call your local dealership and have your chassis number and number plate and they should give it to you over the phone....but i dont think it will come to that..goodluck

Jun 19, 2009 | 2004 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...