Question about Cars & Trucks

1 Answer

Dodge ram headlight switch2007 1500

First started after I adjusted tilt steering wheel2 months ago todat low beams flicker on & off I jiggled light switch and got back on is there a relay or is this the switch did tilt steering wheel cause this thank you bill

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Cars & Trucks Expert
  • 293 Answers

I you jiggle it and it works, then you have something loose, probable a wire in the switch

Posted on Nov 25, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 44 Answers

SOURCE: Low beams only work part time.

Yes it is the wires in the column I do beleive you can replace it but its not a easy job. Wires go from switch all the way doen the column

Posted on Jul 24, 2012

alicantecoli
  • 22156 Answers

SOURCE: Hello, I own a 1996 GMC Sierra with 187,000

look under the shroud and the wiring plug is loose either on the end of the wires or on the switch .

Posted on May 23, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Dodge ram headlights wont work unless dimmer switch pushed


Could be the headlight switch or the dimmer switch.
I would check for voltage at the dimmer switch first.

Sep 17, 2012 | Dodge Cars & Trucks

1 Answer

Low beams only work part time.


Yes it is the wires in the column I do beleive you can replace it but its not a easy job. Wires go from switch all the way doen the column

Jul 24, 2012 | 1997 Dodge Ram

1 Answer

Both headlights do not function on low beam but


there is a bad connection in the switch or the multifunction switch is bad

Feb 09, 2010 | 2004 Toyota Tundra

2 Answers

Low beam headlights do not work ..replaced switch and high beam bulb


try the lights with the tilt wheel in the up position. If the low beam works then, a wire has pulled out of the connector on the mutipurpose switch inside the steering column. remove the covers behind the steering wheel on the column and there is a large multi wire plug with many wires. it should be obvious which wire has pulled out or broken.

Jan 18, 2010 | 1997 Dodge Ram 1500 Club Cab

2 Answers

I have '99 dodge 1500 p/u and the low beams don't work.


its probably the muliti function switch on top the steering column

Dec 30, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

96 gmc yukon headlights will not turn on


Before the lights went out did you have trouble with your high and low beams not always doing what you wanted?If so you'll have to replace your dimmer switch in the column.The wires, over time will fray and break.

Jun 29, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Adjusting headlights on 2001 dodge Ram 2500


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jan 19, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...