Question about 1989 Chevrolet C1500

1 Answer

Slave cylinder location

Ive searched everywhere under the hood and still cant find the slave cylinder.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 171 Answers

For the clutch? Probably under the truck not the hood.

Posted on Nov 25, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the slave cylinder located on a 1982 Ford F 150 with a straight in line v6

I believe you are looking for a master cylinder. A slave cylinder would be on the wheel if talking brakes. If talking clutch, a slave cylinder would be on the bell/flywheel housing between the motor and tranny. The master cylinders for either brakes or clutch would be on the firewall under the hood directly in front of the drivers side.

Oct 12, 2015 | Ford Cars & Trucks

2 Answers

2000 Alfa 166. Just wondering if it is the clutch slave cylinder or the master? or both?

the clutch master cylinder could be a part of the brake master cylinder reservoir
I would suspect that the fault will be the clutch slave cylinder ( cheapest part to start with and most common faulty area
if is not a cylinder outside the bell housing then it will be inside the bell housing and will be expensive to repair as the box has to come out as the slave cylinder sits on the input shaft extension housing of the gear box

Aug 26, 2015 | Cars & Trucks

1 Answer

How do I fix a soft or dead clutch pedal?

Depending on the vehicle (of which there was no posted information in the question) it should be located on the bell housing. UNLESS it's a vehicle equipped with an internal clutch slave which would be located INSIDE the bell housing.

The clutch master cylinder should be located on the firewall under the hood. Sort of looks like a small brake master cylinder.

May 31, 2015 | Cars & Trucks

1 Answer

Where is slave cylinder located on is300

i presume your asking about the clutch slave cylinder ,this will be located under the hood at the bulkhead end of engine compartment ,there will be a small fluid resovoir sitting on top of the actual hydraulic slave cylinder , the clutch fluid resorvoir is smaller , and usually not opaque, than the brake fluid resorvoir, which are usually next to each other , incidentally the brake also has a slave, or more usually known as the master , cylinder

May 13, 2014 | 2005 Lexus Is 300

1 Answer

Hot to fix a clutch that goes all the way to the floor

Check your clutch master cylinder's fluid,it's located under hood in right corner,if low or empty,then your slave cylinder is bad and leaking,it's connected to side of transmission.Here's a link. Repair Guides Clutch Clutch Release Cylinder AutoZone com Here's the part. Duralast Clutch Slave Cylinder 12425 1992 Nissan Datsun D21 Truck 2WD 4...

Jan 14, 2014 | 1992 Nissan Pickup

1 Answer

Where is slave cylinder on tt quattro

slave cylinder easiest one to inspect first will be down at gearbox
master cylinder will be under hood opposite the clutch pedal
check fluid level first and top up

Sep 27, 2012 | Jeep Wrangler Cars & Trucks

1 Answer

Where is the Master and Slave Cylinder located on my 2000 Honda Prelude

Might help if you gave a clue as to whether you are asking about the clutch or the brakes, they both have both. Open the hood and look directly in front of where you push when you push the brake or clutch. Mounted on that wall under the hood you will see two reservoirs, one is master for brake and the other master for clutch. There is a slave for the clutch attached to the bell housing where it attaches to the engine, and each wheel's brake has a slave for the brakes.

Some companies have made a shared master cylinder, so there is some possibility there would be but one master cylinder. You would know that if both systems have failed together.

Apr 19, 2011 | 2000 Honda Prelude

1 Answer

Clutch pedal droped raisded back by hand pedal does not depres engine does not start

It sounds like your clutch master or slave cilinder has gone bad .you should be able to locate clutch cylinder under hood usually drivers side check fluid level if low replace master or slave cylinder.

Nov 26, 2010 | 2004 Hyundai Santa Fe

1 Answer

I have a 1996 ford f-150 and my clutch just sticks to the floor. It doesnt retract.

Check the clutch fluid, under the hood on the firewall, if the fluid is low then you need to inspect the for a leak. This could be a leaking slave cylinder which is located internal of the trans bellhousing, if you see any dampness this would indicate a slave cylinder leak. Replacement of the slave , line , and the master cylinder will be required. The slave and master have been updated and require all three to be replaced. Thankyou ,Please rate this answer This will help me out .

May 30, 2010 | 1996 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides