Question about Cars & Trucks

Open Question

Engine timing marks

Hi need timing mark diagram for a chana star 1300 2008 model

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ewashmidas
  • 362 Answers

SOURCE: TIMING MARKS FOR GALANT

Here you go...

e40a0ab.png

Posted on Feb 02, 2009

  • 383 Answers

SOURCE: need timing belt mark diagram for 95 corolla 4afe

malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.

Posted on May 06, 2009

skdeepak88
  • 232 Answers

SOURCE: desparetly need diagram for 1990 volkswagen golf 1.8 timing marks

http://images.eurotuner.com/images/eurp_0801_07_z+2001_vw_golf_1-8t+1-8_liter_20v_engine_atp_gt28rs_turbo_vf_engineering_engine_mount_usrt_genesis_415cc_injectors.jpg please rate me!!

Posted on Aug 16, 2009

ZJLimited
  • 17970 Answers

SOURCE: need diagram showing timing adjustment for a 1992

Check the position of the timing marks. The timing pointer mustbe perfectly aligned with the TDC (white mark) on the flywheel orflex-plate; the camshaft pulley must be aligned so that the word UP isat the top of the pulley and the marks on the edge of the pulley arealigned with the surfaces of the head. Additionally, the face of thefront timing balancer pulley has a mark which must be aligned with thenotch on the oil pump body. This pulley is the one to the left crankwhen viewed from the pulley end.

Also, in here, 1994-Honda-Accord-Coupe-Section-01-Engine (page 47 and next / TDC marks) you can find referenece information about Accord Engine.

If you need more details, visit autozone.com (free register) and select your model vehicle.

I hope help you (remember rated this help) Good luck.

Posted on Sep 25, 2009

  • 1 Answer

SOURCE: Hi,I need to know where

Hi gud am!can i ask for the firing order of toyota 2c engine

Posted on Apr 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

About the Chana star 2007 engine numbber


VEHICLE IDENTIFICATION NUMBER The vehicle identification number "1" is stamped into the right side of the steering head pipe.

Feb 16, 2016 | Cars & Trucks

1 Answer

Looking for timing marks on chana star engine


should be on block and cam gear where the belt or chain is .

Jan 16, 2016 | Cars & Trucks

1 Answer

I looking for a workshop manual book for chana star light panel van 1000cc


Where can i downlaid a workshop manual for a Chana Star ...

www.fixya.com/cars/t20864169-downlaid_workshop_manual_chana
Oct 21, 2013 - where can i downlaid a workshop manual for a Chana Star 1.3 ... As with any manual transmission, light or heavy duty, popping out of gear ... Where do I find the gearbox oil filler plug on Chana Star 1.3 panelvan ... Hi, my Chana Star 1000cc has problems with idle, normally it idles ... Manuals & User Guides.

#Tags chana auto repair manual


Nov 28, 2015 | Cars & Trucks

1 Answer

Loking for illustration off chana star valve timing marks urgent and does if bent valves if putted valve timing incorrectly


Hi there
Well if you done the motor and you havent timed it correctly then you will get a knocking noise and dependens on the motor then yes it could bend the push rods or tight tappets or out of timing the valves can bend,hole in pistons bent rockergear etc.
But depends on the motor if you time it with number 1 piston is TDC number 1 and last valves rocking [depending on how many cylinders you have 4 /6/ etc and set distributor firing No 1

Nov 16, 2014 | Cars & Trucks

1 Answer

Hi i am looking for a diagram that can help me set the timing belt timing on a chana 1000 star


I'm sure if you are replacing the timing belt then you know what you are doing, but I don't know how to describe how to do it without knowing the year, make, model and engine size. I am sure there is not a diagram to go by, but it is a precise order of taking the assembly out and replacing it so , if you need that information I will need your information Please. Hope to Help.

Feb 02, 2014 | Cars & Trucks

1 Answer

I need a diagram of engine timing marks for audi A8 V6 engine 3.0L


you dont need a diagram to see the timing marks on the top/bottom pulleys,just clean them off and run a piece of chalk around the perimeter.they are a bit obvious

Sep 13, 2012 | 2005 Audi A8

1 Answer

I have audi A8 2005 model V6 engine 3.0L need timing mark location


the timing marks are located on the pulleys , clean them off & then run around the pulleys with pool cue chalk, the timing marks are plainly visible after this little trick/tip.

Sep 13, 2012 | 2005 Audi A8

1 Answer

Need timing belt marks for 1999 kia sportage diagram


  • Hi, I can help. Please see the diagrams below for your timing marks.

  • The picture below is the crankshaft marks that need to be lined up before you remove the timing belt.
ironfist109_30.png
  • Below is the intake and exhaust camshaft pulley marks.

ironfist109_31.png


  • Below is an exploded diagram of the engine components in relation to the timing belt.

ironfist109_32.png
  • Please not that this diagram is good for both 4X4 and 2X4 2.0 Engine (which is the only engine Kia Sportage had that year).

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Aug 27, 2011 | Kia Sportage Cars & Trucks

2 Answers

How do u adjust the timing i must have moved the pullies when i was putting on the timing belt after i changed the water pump now its not runnin smooth its off how do i put it back in time


There are marks that you have to line up. The folowing pictures are for DEMOSTRATION PURPOSE ONLY- YOUR MARKS MIGHT BE DIFFERENT. Once all the marks are lined up then you can install the belt, set the tension and rotate the engine two full turns to make sure all the marks line up.

chuckster57_31.gif
chuckster57_32.gif

Apr 18, 2011 | Kia Spectra Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...