Question about 2006 Volkswagen Touareg

1 Answer

No signal detected

Hi, My Touareg complains of no signal from the Engine Speed Sensor. We have replaced the sensor with a new one and the problem still persist. It wont start. Please do you have any possible solution that can help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

Check connection for corrosion clean an if still not working take the sensor back to be checked out to see if it is faulty happens a lot.....

Posted on Nov 26, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

salvidordali
  • 103 Answers

SOURCE: NOX SENOR

I have yet to see a car with a Nitrogen Oxides(NOx) sensor on it. However I have seen Oxygen (O2) sensors. The O2 sensor monitors the remaining amount of oxygen left in your exhaust, and tells your Engine Control Unit(ECU) how much fuel to use. The sensor looks much like a stainless steel spark plug and is found in the exhaust system. Your car being a 1991 it should only have one. It will be up stream of the Catlytic converter, maybe in the Exhaust manifold. cost between 50 and 150$us.

Posted on Jan 09, 2009

  • 64 Answers

SOURCE: 1999 volkswagen stalled

first check cylinder 1 , spark plug, ht leads, coil,

then clean the trottle body with carb cleaner

if that does not work replace the throttle body, comes complete, and do a basic setting on it with diagnostic machine

Posted on Feb 19, 2009

pippall
  • 1486 Answers

SOURCE: reset computer on 2004 Touareg

Drive the car at about 10 mph then if there is no fault the light will go out.Failing that remove the baterry wires and leave off for an hout then replace.That should cllear the code.Make sure you have the radio code before you disconect the baterry.Hope that was helpfull.Good luck.

Posted on Jul 28, 2009

youngenginee
  • 57 Answers

SOURCE: High Emissions

sorry if that is the code it is not correct with the obd format it surpose to have something like P0033 re-check and let us know the correct code

Posted on Aug 01, 2009

  • 138 Answers

SOURCE: engine speed sensor location, 2001 vw bug

The Engine speed sender is located on the front of the engine block at the level of the crankshaft near to the gearbox bell housing.

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My guages stoped working and transmition seems to be slipping in my 2001 shevy silverado 4.8


Well ronnie do you know how to do automotive electrical testing with a volt meter ? How to read an understand a wiring diagram ? Would think not to be a relay problem because other thing's would not work as well ! More then likely a loose ground or something on that order ! Plus you must mean Ignition . 1 relay , because there isn't a eng.1 relay . Ign. 1 relay powers the PCM - engine computer , fuel injectors , the TAC - electronic throttle control module . Do the instrument cluster lights still work when the gauges quit ? Looking at power distribution diagram I see a engine 1 fuse but has nothing to do with the instrument cluster . Supply's B+ voltage to the maf sensor , EVAP system , CAM sensor , IAT sensor , fuel pump relay ! Could be a communication problem on class 2 data bus . All the modules on the vehicle share information on the class 2 bus . The gauges get thier info from the PCM over this data network !
Engine Coolant Temperature Gauge
The IPC displays the engine coolant temperature as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine coolant temperature. The engine coolant temperature gauge defaults to 75°C (160°F) or below when:
• The PCM detects a malfunction in the engine coolant temperature sensor circuit.
• The IPC detects a loss of class 2 communication with the PCM.

Fuel Gauge
The IPC displays the fuel level as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the fuel level percent. The fuel gauge defaults to empty if:
• The PCM detects a malfunction in the fuel level sensor circuit.
• The IPC detects a loss of class 2 communications with the PCM.
When the fuel level is less than a pre-determined value, the low fuel indicator illuminates.
Reviewing the fuel system description will further explain how the system functions. Refer to:

Speedometer
The IPC displays the vehicle speed based on the vehicle speed signal from the PCM. The IPC receives the vehicle speed signal via a discreet wire. The IPC uses the vehicle speed signal circuit (4000 pulses/mile) from the PCM in order to calculate the vehicle speed. The speedometer defaults to 0 km/h (0 mph) if a malfunction in the vehicle speed signal circuit (4000 pulses/mile) exists.

Tachometer
The IPC displays the engine speed based on the engine speed signal from the PCM. The IPC receives the engine speed signal from the PCM via a discreet wire. The IPC uses the engine speed signal circuit (2 pulses/engine revolution) from the PCM in order to calculate the engine speed. The tachometer defaults to 0 rpm if a malfunction in the engine speed signal circuit (2 pulses/engine revolution) exists.
Transmission Temperature Gauge
The IPC displays the transmission temperature as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the transmission temperature. The transmission temperature gauge will default to 40°C (100°F) or below if:
• The PCM detects a malfunction in the transmission temperature sensor circuit.
• The IPC detects a loss of class 2 communications with the PCM.
Voltmeter
The IPC displays the system voltage as detected at the ignition 1 input of the IPC. When the engine is ON, the gauge should be between 10 and 16 volts.

The only one that has a hard wired sensor is the oil pressure gauge.
Engine Oil Pressure Gauge
The IPC uses the engine oil sensor signal to determine the engine oil pressure. The oil pressure sensor signal circuit is hard-wired to the IPC. The engine oil pressure sensor signal to the IPC is a variable resistance ranging from 0-90 ohms. A sensor resistance of 1 ohms will display as 0 psi (0 kPa) and a resistance of 88 ohms will display as 80 psi (550 kPa). The Check Engine Oil Pressure indicator will be displayed in the message center if the IPC detects a low engine oil pressure.

Does this one drop out also ? quit working

I would suggest that you take an have the IPC checked for DTC'S - diagnostic trouble codes , NOT OBD 2 engine codes , these are different an need a professional type scan tool .
You could check G103 for being loose . G103
On the left rear of the engine block . Also pull the instrument cluster out an check connection at the back of IPC . Check power an ground circuits at the PCM as well . You can fine wiring diagrams here
http://www.bbbind.com/free_tsb.html Enter the vehicle info . year , make , model an engine . under system click body an acc. then under subsystem click on instrumentation .Click the search button , then click the blue link . At the top of the diagram it shows B+ power supply , The connectors on the back of IPC , A,B , plus the pin # an color wire .
PCM power and ground testing avi
How To Use Multimeter Test Car Ground Video 3
Intermittent Electrical Diagnostics with Rich Peterson


Apr 10, 2017 | Cars & Trucks

2 Answers

My 1996 Toyota Avalon was making a knocking sound while driving on the freeway then stalled the engine will not come back on it just makes a clicking sound and the code reads p1705


That code relates to the transmission:
It's the sensor that sits directly on top of the transmission case.. Easy fix.
This sensor detects the rotation speed of the direct clutch drum.
By comparing the direct clutch speed signal with the vehicle
speed sensor signal, the ECM detects the shift timing of the
gears and appropriately controls the engine torque and hydraulic
pressure in response to various conditions, thus performing
smooth gear shifting.
DTC No. DTC Detecting Condition Trouble Area
P1705
The ECM detects conditions (a), (b), (c), (d), (e) and (f) continuity
for 4 secs. or more.
(2?trip detection logic)
(a) Vehicle speed : 32 km/h (20 mph) or more
(b) 3rd or 4th gear
(c) NC2 < 300 rpm
(d) Park/neutral position switch: OFF
(e) Solenoid valves and vehicle speed sensor are normal
(f) L position: OFF
 Open or short in direct clutch speed sensor circuit
 Direct clutch speed sensor
ECM
WIRING DIAGRAM
DI02P?03


according to this site:
Error code P1705

It's not why your car won't start.

Mar 09, 2016 | Toyota Cars & Trucks

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

2000 galantwhat is codep0715


P0715 MITSUBISHI - Input/Turbine Speed Sensor Circuit Malfunctionpdf.gif? comments.gif ' Add Commentxicon.jpghttp://engine-codes.com/p0715_mitsubishi.htmlForum CodePossible causes - Transmission speed sensor circuit is open or shorted
- Transmission speed sensor circuit poor electrical connection
- Faulty transmission speed sensor
help.png Help with thisWhen is the code detected?Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Possible shifting problemsP0715 MITSUBISHI Description The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).
Need more help?Do you need more help with the P0715 MITSUBISHI code? ask a question to our users or search the top hand picked automotive forums for more information

Read more: http://engine-codes.com/p0715_mitsubishi.html#ixzz2QYRb9Yyu
Follow us: EngineCodes on Facebook

Apr 14, 2013 | 2006 Honda Accord

1 Answer

What does codes 64 63 11 09 and 21 0n 2005 dodge stratus mean


CODE 11 No distributor referene signal detected during engine cranking....Check circuit between the distributer and the pcm.

CODE 12 Problem with battery connection.Direct battery input to pcm disconnected within the last 50 ignition key-on cycles.

CODE 13** Indicates a problem with map sensor vacuum system.

CODE 14** map sensor voltage to high or to low.

CODE 15** Problem with vehicle speed sensor signal.No vss signal detected during road load conditions.

CODE 17 Engine is cold to long.Engine coolant temp stays below normal operating temp(check thermostat).

CODE 21** Problem with oxygen sensor signal circuit.Sensor voltage to computer not fluctuating.

CODE 22** Coolant sensor voltage to high or to low.Test coolant temp sensor.

CODE 23** Indicates that the air temp sensor input is below the minimum acceptable voltage or sensor input is above the acceptable voltage.

CODE 24** Throttle position sensor voltage to high or low.Test the tps.

CODE 25** Idle air control (IAC) valve circuits.A shorted condition is detected in one or more of the IAC valve circuits.Or a vacuum leak has been detected.

CODE 27 One of the injector control circuit output drivers does not respond properly to the control signal.Check the circuits.

CODE 31** Problem with canister purge solenoid circuit.

CODE 32** An open or shorted condition detected in the EGR solenoid circuit.Possible air/fuel ratio imbalance not detected during diagnosis.

CODE 33 Air conditioning clutch relay circuit.An open or shorted condition in the compressor clutch relay circuit.

CODE 34 Open or shorted condition in the speed control vacuum or vent solenoid circuits.

CODE 35 Open or shorted condition detected in the radiator fan low speed relay circuit.

CODE 37** Open or shorted condition detected in the torque converter part throttle unlock solenoid control circuit.

CODE 41** Problem with charging system.An open or shorted condition detected in the generator Field control circuit.

CODE 42 Fuel pump relay or auto shutdown relay (ASD) control circuit indicates an open or shorted condition.

CODE 43** Multiple cylinder misfire detected.Peak primary circuit current not achieved with the maximum dwell time.

CODE 44 Battery temperature sensor volts malfunction.Problem with the battery temperature voltage circuit in the pcm.

CODE 46** Charging system volts to high>Computer indicates that the battery voltage is not properly regulated.

CODE 47** Charging system voltage to low.Battery voltage sense input below target charging voltage during engine operation and no significant change in voltage detected during active test or alternator output.

CODE 51** Oxygen sensor signal input indicates lean air/fuel ratio condition during operation.

CODE 52** Oxygen sensor signal input indicates rich air/fuel ratio during engine operation.

CODE 53** internal pcm failure detected.

CODE 54** No camshaft position sensor signal from distributer.Problem with the distributer synchronization circuit.

CODE 55 Completion of fault code display on check engine lamp.this is end of message code.

CODE 62 Unsuccessful attempt to update EMR mileage in the controller EEPROM.

CODE 63** Controller failure.EEPROM write denied.Check the PCM

Dec 12, 2012 | 1995 Dodge Stratus

3 Answers

Error code p2138


Here is the definition. You may need to have someone check the accelerator pedal position sensor and the circuit.

P2138 NISSAN Description The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the Engine Control Module (ECM).
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
Read more: http://engine-codes.com/p2138_nissan.html#ixzz26J3D2x8s

Sep 12, 2012 | 2010 Nissan Versa 1.8

1 Answer

Which codes (OBDI or II) do I use for my 1994 Jeep Grand cherokee laredo 4.0 2wd


before 1996 they use onboard diagnosis system for jeep.

when you turn on key you need to count check engine light blinks.

here are codes taken from internet.

11* No crank reference signal detected during engine cranking.
12* Direct battery input to PCM was disconnected within the last 50 key-on cycles.
13** No difference recognized between the engine MAP reading and the barometric (atmosphereic) pressure reading at start-up
14** MAP sensor input below minimum acceptable voltage.
or
MAP sensor input above maximum acceptable voltage.
15** No vehicle distance (speed) sensor signal detected during road load conditions.
17* Engine coolant temperature remains below normal operating temperatures during vehicle travel (thermostat).
21** Neither rich nor lean condition detected from the oxygen sensor input.
or
Oxygen sensor input voltage maintained above the normal operating range.
22** Engine coolant temperature sensor input above maximum acceptable voltage.
or
Engine coolant temperature sensor input below minimum acceptable voltage.
23** Intake manifold air temperature sensor input above maximum acceptable voltage.
or
Intake manifold air temperature sensor input below minimum acceptable voltage.
24** Throttle position sensor input above maximum acceptable voltage.
or
Throttle position sensor input below minimum acceptable voltage.
25** A shorted condition detected in one or more of the idle air control motor circuits.
27* Injector #1 output driver does not respond properly to the control signal.
or
Injector #2 output driver does not respond properly to the control signal.
or
Injector #3 output driver does not respond properly to the control signal.
or
Injector #4 output driver does not respond properly to the control signal.
or
Injector #5 output driver does not respond properly to the control signal.
or
Injector #6 output driver does not respond properly to the control signal.
33* An open or shorted condition detected in the A/C clutch relay circuit.
34* An open or shorted condition detected in the speed control vacuum or vent solenoid circuits.
or
Speed control switch input below the minimum acceptable voltage.
or
Speed control switch input above the maximum acceptable voltage.
35* An open or shorted condition detected in the radiator fan relay circuit.
41* An open or shorted condition detected in the generator field control circuit.
42* An open or shorted condition detected in the auto shutdown relay circuit.
44* An open or shorted condition exists in the engine coolant temperature sensor circuit or a problem exists in the PCM's battery temperature voltage circuit.
46** Battery voltage sense input above target charging voltage during engine operation.
47** Battery voltage sense input below target charging voltage during engine operation. Also, no significant change detected in battery voltage during active test of generator output.
51** Oxygen sensor signal input indicates lean air/fuel ratio condition during engine operation.
52** Oxygen sensor signal input indicates rich air/fuel ratio condition during engine operation.
53* PCM internal fault condition detected.
54* No fuel sync (camshaft signal) detected during engine cranking.
55* Completion of diagnostic trouble code display on the malfunction indicator lamp (check engine lamp).
62* Unsuccessful attempt to update SRI (service reminder indicator) miles in the PCM EEPROM.
63* Unsuccessful attempt to write to an EEPROM location by the PCM.

* - Check engine lamp will not illuminate at all times if this code was recorded. Cycle ignition key as described and observe code flashed by check engine lamp.

** - Check engine lamp will illuminate during engine operation if this code was recorded.

PCM = Powertrain Control Module (the engine computer)
MAP = Manifold Absolute Pressure (the sensor that measures how hard the engine is sucking air through the intake manifold
EEPROM = Electrically Erasable Programmable Read Only Memory (a type of computer chip used inside the PCM)

Nov 19, 2011 | 1994 Jeep Grand Cherokee

1 Answer

1998 Chrysler Sebring convertible Not shifting into drive check engine light came on, error code PO715


DTC P0715 CHRYSLER - Input Speed Sensor 1 Circuit
P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible shifting problems

Possible causes
- Transmission speed sensor circuit is open or shorted.
- Poor transmission speed sensor circuit connection
- Faulty transmission speed sensor

Hope this clues helps to solve it.

Jun 02, 2011 | 2003 Chrysler Sebring

1 Answer

Is there a list for computer codes for 1980-1990's Chrysler Le Baron


Yes here is that list.
Chrysler products COMMON CODES OBD1 (vehicles made before 1995)
Part 1: Chrysler Domestic vehicles
CODES/Meaning
88 display used for start or test
11 camshaft signal or ignition signal, no reference signal during cranking
12 memory to controller has been cleared within 50-100 engine starts
13 map sensor not detecting any change during test
14 map voltage too high or too low
15 vehicle speed sensor, no signal detected
16 knock sensor circuit. open or short detected
17 low engine temperature, possible thermostat fault
21 oxygen sensor signal, neither rich or lean detected
22 coolant sensor voltage low
23 air charge voltage high/low detected
24 throttle positioner sensor voltage high/low
25 automatic idle speed motor driver circuit, short or open detected
26 injectors 1,2,3 peak current not reached
27 injector control circuit does not respond to control signal
31 purge solenoid circuit, open or short detected
32 egr solenoid circuit, open or short detected
33 a/c clutch relay circuit, open or short detected
34 speed control servo solenoid, open or short detected
35 radiator fan control relay circuit, open or short detected
36 wastegate solenoid, open or short detected
37 part throttle unlock(PTU) circuit, open or short detected
41 charging system circuit not responding to control signal
42 fuel pump or auto shutdown (ASD) relay voltage sensed at controller
43 ignition control circuit not responding
44 battery temperature voltage circuit problem
45 turbo boost limit exceeded-map sensor detects overboost
46 battery voltage too high
47 battery voltage too low
51 air/fuel at limit
52 logic module fault
53 internal controller failure
54 camshaft reference circuit not detected
55 end of message
61 baro read solenoid, open or short detected
62 emr mileage not stored
63 eeprom write denied
64 flex fuel sensor signal out of range
65 manifold tuning valve, open or short detected
66 no ccd messages
76 ballast bypass relay, open or short detected
77 speed control relay, open or short detected

May 31, 2011 | Chrysler LeBaron Cars & Trucks

2 Answers

Trouble code P0320 ignition/dist. engine speed input circuit


P0320 - Ignition / distributor engine speed circuit malfunction

The ignition engine speed sensor input signal to Powertrain Control Module (PCM) or Electronic Control Module (ECM) is continuously monitored. The test fails when the signal indicates that 2 successive erratic profile ignition pickup (PIP) pulses occurred.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- The engine may be harder to start
- The engine may stumble or stall

When is the code detected?
The P0320 code is triggered when 2 successive erratic PIP pulses are detected.

Possible Causes:
- Loose wires/connectors
- Faulty Crank Position Sensors
- Arcing secondary ignition components (coil, wires and plugs)
- Low battery charge
- Powertrain Control Module

Possible Solutions:
- Resecure loose wire or connectors
- If battery charge is low, recharge or replaced battery
- Replaced crank position sensor
- Replaced starter motor


Test it and tell us news.

Nov 18, 2010 | 2004 Ford Explorer

Not finding what you are looking for?
2006 Volkswagen Touareg Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...