Question about 1997 Ford Probe

1 Answer

Need diagram of air vendolation system ,possibly a dead mouse in it.

Diagram of air vendolation system of 97 ford probe

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 221 Answers

Click Here for full package of wiring diagrams of your Ford Probe 1997

Good luck

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause a 97 Ford Probe GT to idle rough and misfire at idle only Buck Run better when it's cooler outside and it also stalls when it has a rough idle


Check for any sources of unmetered air entering the engine. ( Vacuum leaks ). Check air intake hose going from air filter box to throttle assembly for any signs of splits/cracking causing a lean condition. Possible Air flow sensor dirty/defective

May 27, 2016 | Ford Cars & Trucks

2 Answers

89 ford probe hesitates when leaving a red light, then runs fine otherwise, fuel filter?


Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard ...

repairpal.com > Problems > Ford > Probe
Ford Probe Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard Starting, Poor Performance. This is a verified problem based on 9 reports. Learn more ...

Starting Problems - 1997 Ford Probe - RepairPal

repairpal.com > Questions > Ford > Probe > 1997 Ford Probe
Dec 5, 2010 - Starting Problems on 1997 Ford Probe ... If the engine runs rough,stalls, hesitates on acceleration, is hard to start, or has generally poor ...

A new misfire/hesitation on accel. Problem.. - ProbeTalk.com Forums

forums.probetalk.com > Tech Section > 2nd Gen (93-97) V6 2.5L

Feb 05, 2016 | Ford Cars & Trucks

1 Answer

FORD PROBE


Sounds like you may have water in the system. If that they case you'll need to have the system evacuated and refilled by a professional. It'll probably need to have the dryer cartridge replaced as well.

Jun 15, 2012 | 1995 Ford Probe

4 Answers

Vaccum hose diagram


what type of ford what year

Dec 01, 2010 | Ford E-250 Cars & Trucks

1 Answer

My vacuum lines for my 97 ford probe 4cyl, got all messed up by transmission shop. was wondering if anyone could help. loked underhood but isnt very precise on its diagram


Having owned a trans shop ,that brings back some bad memories ,of what your employees do.

Take it back. Put the pressure on them. There is no excuse for the way they work. I have lived that life.

Sep 19, 2010 | 1997 Ford Probe

1 Answer

Need diagram for steering column for 97 ford


if the key turns fully as it suppose to the electrical ignition switch is at fault

Apr 02, 2010 | 1997 Ford Taurus

1 Answer

How to set timing on 97 ford probe gt


This is the specs...not too sure on what else you are asking about:

d23bf61.gif
Save to desktop and then zoom.

Jun 23, 2009 | 1997 Ford Probe

1 Answer

1995 ford probe


The mass air flow sensor is right by the airbox.... It has two screws holding it into a body. Unplug it, unscrew it, and take it out of the housing. Its literally in plain view. Take it out and CAREFULLY put the new one in. Make sure not to damage the electrodes on the new mass air flow sensor. It's not even six inches from where you put in the air filter. Intake hose going to the intake manifold.

Jun 10, 2009 | 1995 Ford Probe

1 Answer

Im putting a brake line on for a 2003 Ford Contour and i need a diagram


You have the best possible diagram: look at your brakeline and duplicate as best you can. (does not have to be perfect, just has to be connected well on both ends and not interfere with any moving parts). avoid places where it could rub through and use small sections of rubber hose to eliminate vibration and rubbing Use as many of the original fasteners as possible along the line. Bleed system completely when installed.

Mar 27, 2009 | 1994 Ford Probe

1 Answer

How do you set the timing marks on 97 ford probe?


what marks are used when setting timing on 1997 ford probe

Oct 19, 2008 | 1997 Ford Probe

Not finding what you are looking for?
1997 Ford Probe Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...