Question about 1997 Chevrolet Venture

1 Answer

Rockervalve head torque 3.4 liter

Whats the torque on rocker arm valve on 3.4 liter and could they be titend induelvedly differently.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

168 in. Lb. Which equals 14 ft./lb.also tighten additional 30 degrees after you reach torque.good luck

Posted on Dec 03, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

ourhowse
  • 2007 Answers

SOURCE: putting distributor back in the right way

Okay. Turn the engine untill you have the crank mark lined up with the 0 on the pointer. At that point, look at the valves on #1 cylinder. They should both be closed, or in the "up" position. If they aren't, you'll have to turn it one revolution, to get to compression stroke. Now, you're ready to put the distributor in. Take the top off the cap, and position it in the hole, so that the rotor lines up with #1 on the distributor cap. If it's a newer one, take a close look inside at where #1 actually is because the newer ones are off set a little. Now, tighten the cap on, and hook up the plug wires, one at a time in the proper order and rotation. When you try to start it, it should run where it is, but you may have to turn the distributor slightly one direction or the other to make it start. Try your best to keep it running for 20 minutes or so the first time so your gaskets will set. ( not always an easy task when the valves aren't adjusted, and antifreeze can still vapour lock on you) If you need to know more, let me know.

Posted on Nov 13, 2009

Testimonial: "Thank you , but still hoping i had it at tdc to start with when i set the rocker arms but checked comp good on all but #1 and #3 "

ftw1952
  • 10319 Answers

SOURCE: torque specs for the rocker arms of a 1997 malibu

31 foot pounds

Posted on Mar 04, 2010

  • 94 Answers

SOURCE: I have a 2001 chevy

Hello,

You are correct there is no lash adjustment, just the torque. However you do have to rotate the crankshaft balancer to position the crankshaft balancer alignment mark 57-63 degrees clockwise or counterclockwise from the engine front cover alignment tab. No further adjustment is required. By the way I have 22 Ft. Lbs for that torque (probably doesn't matter much) I hope this helps.

Posted on Sep 04, 2011

  • 37 Answers

SOURCE: 2005 equinox with 3.4 what is rocker arm torque ?

31 ft lbs

http://screensnapr.com/e/CY3RQt.png

image

Posted on Jan 04, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the rocker arm torque specs on a 1996 dodge caravan 3.0 liter


Hi Derrel,here's a link to a Autozone repair guide on your rocker arms,you can join their site like me for free and use all their repairs guides,need more help,let me know,k. Repair Guides Engine Mechanical Rocker Arm shafts AutoZone com

Aug 29, 2016 | 1996 Dodge Caravan

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

Rocker arm installation 99 monte carlo 3.1


Once valve cover is removed then there is a single bolt holding rocker arm assembly to head usually a 10mm bolt remove and remove rocker are and stand replace all make sure that you align stand up as you tighten bolt torque to 10-15 ft lbs + 30 degrees

Mar 21, 2014 | 1999 Chevrolet Monte Carlo

2 Answers

Valve lash procedure


i need to know how to adjust the valves on 02 pont sunfire

Nov 20, 2011 | 1991 Chevrolet K1500

2 Answers

Rocker arm torque specs on a 2001 chevy malibu 3.1


Rocker arm torque specs for the bolts are 14 Nm (124 inch lbs.)

Apr 15, 2011 | 2001 Chevrolet Malibu

1 Answer

I need to know what the cyl head torque and rocker arm torque is for a 1998 6.5 L GM turbo diesel.


Cylinder head bolts are done in 3 steps. Step 1 - 20 ft.-lbs
Step 2 - 50 ft.-lbs
Step 3: Tighten an additional
90 degrees.
Lifter guide plate bolts 18 ft-lbs
Rocker arm shaft bolts 40 ft-lbs
Hope this helps.

Aug 06, 2010 | 1999 GMC Sierra 3500

1 Answer

4.3 liter, Rocker nuts back off at idle


I would try using some Loctite Threadlocker, they offer different strengths, removable and non-removable.

May 15, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

I have 4.9L6 need torque specs for cylinder head


for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Dec 05, 2009 | 1988 Ford F 150

1 Answer

Need head bolt,intake upper and lower and rocker arm torque lbs.


Head bolts--------- 22 ft lbs.
Intake upper------ 18 ft lbs.
Intake lower------- 10 ft lbs. Tighten vertical bolts first, the diagonal bolts, failure to do this will result in an oil leak.
As far as the rocker arm bolts, they have to be adjusted with the valves closed, tighten down just enough to turn the push rods with your fingers with slight tension.
This is out of a Technical Specifications Manual.

Jul 30, 2009 | 2002 Pontiac Grand Am

Not finding what you are looking for?
1997 Chevrolet Venture Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...