Question about Volvo Cars & Trucks

Open Question

Exterior door handle repair - Volvo Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 341 Answers

SOURCE: Replacing exterior door handles 1998 Safari van

remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle

Posted on Nov 14, 2008

  • 508 Answers

SOURCE: How to replace '96 Ford Explorer driver side exterior door handle

You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Posted on Feb 18, 2009

motorhead427
  • 24 Answers

SOURCE: Need instructios to repair 1997 Toyota Camry Broken Exterior Door Handle

Two 10mm bolts, or nuts, hold the handle on from inside the door. dont forget to remove actuating rod from old handle. probably clip is broke also.

Posted on May 30, 2009

wireguy212
  • 1627 Answers

SOURCE: replacement exterior door handle

you will need to get the door panel off the inside,undo the linkages and the remove the nuts holding the handle on.

Posted on Jul 28, 2009

  • 1986 Answers

SOURCE: replace exterior door handle on a jeep commander

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door

Posted on Oct 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I repair the exterior door handle on a 1999 Toyota Camry ? Will it be necessary to replace the entire door ?


No the door handle is easily replaceable. you do have to remove the door panel and roll the window all the way up. 2 10mm nuts inside the door cavity and one bolt on the door jam near the lock mechanism. These handles are made of plastic and degrade and break easily after 3 or 4 years. Every toyota owner has to deal with this at some point. I also recommend buying the new handles on ebay as opposed to the dealer. The aftermarket handles are better quality than the original and MUCH cheaper. They are ALWAYS available on ebay.

Aug 02, 2012 | 1999 Toyota Camry

1 Answer

2006 VW Jetta. Exterior door handle does not work.


likely one of the bars has fallen off and will just require a clip from dealer if anything

Jan 22, 2010 | Volkswagen GLI Cars & Trucks

2 Answers

Need instructios to repair 1997 Toyota Camry Broken Exterior Door Handle


Two 10mm bolts, or nuts, hold the handle on from inside the door. dont forget to remove actuating rod from old handle. probably clip is broke also.

May 30, 2009 | 1997 Toyota Camry

1 Answer

Replace left front door outside handle pot metal tip broke off


SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Exterior Front Door Handle Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. NOTE: The tie strap does not need to be reinstalled.
    If equipped, remove the tie strap from the anti-theft guard.
  1. Remove the screws and position the anti-theft guard aside.
  1. Release the clip and disconnect the exterior door handle actuating rod.
88661dd.gif
  1. Remove the anti-theft guard.
  1. Remove the exterior door handle screw.
  1. Remove the exterior handle actuating rod.
  1. Remove the exterior door handle lock cylinder cover.
  1. Remove the exterior door handle.

Apr 25, 2009 | 2001 Ford Escape

1 Answer

Driver's door is not opening using exterior door handle


Normally it will be the small retainer that holds the inside of the door handle to the part that hooks to the latch assembly. Or it is possible that the door handle part is broken, but not likely. You will have to have the window raised, and remove the door panel and look inside the door panel where the handle attaches to see what the problem is. May help to have a flashlight. These are sometimes difficult to fix as there is not much room to work & the parts have to be attached for the exterior handle to work. Rick

Apr 15, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How to remove driver door outside door handle


Remove the front door trim panel.
Peel back the watershield.
Remove the exterior door handle access hole grommet from the door.
Loosen the screw.
The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw.
Remove the door lock cylinder bezel.
Slide the exterior door handle to release.
Remove the exterior door handle and gaskets.

Feb 25, 2009 | 2000 Ford Focus

1 Answer

Diagram for replacing exterior door handles


ok. first u remove the door panel(s), with the window rolled up, u will be able to see the back side of the exterior door handle. there will be three bolts, they are size 10metric. there is also a rod attached to the handle held in place by a plastic clip, remove the rod, then remove the three bolts. from the outside remove the exterior door handle being careful not to scratch painted surface. Repeat for the other door(s). Repeat this for installation.

Dec 14, 2008 | 1997 Toyota Camry

1 Answer

Briver's door handle (exterior)


take door panel off but make sure window is up first. then unclip the rods that are connected to the handle. then unscrew the 2 bolts that are holding the door handle in. then take the handle out and put the new one in and put it back together.

or just go down and get a repair manual at your local auto parts store for less then 20 dollars

Dec 07, 2008 | 2002 Hyundai Accent

1 Answer

2001 Nissan Quest - Broken Exterior Sliding Door Handle


you can do this. you have to remove inside trim panel for access. if you still need to do, I will send you repair steps. let me know

Oct 16, 2008 | 2001 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...